OctoPrint - "unhandled communication error"

Oprogramowanie sterownika drukarki i do łączenia komputera z drukarką
StudioKamar
Konto z ograniczeniami
Postów w temacie: 16
Posty: 207
Rejestracja: 14 sty 2018, 18:34
Lokalizacja: Żnin
Drukarka: Anet A8
x 10

OctoPrint - "unhandled communication error"

Post autor: StudioKamar »

Mam pytanie czy ktoś się spotkał z takim problemem ?? Ostatnio miałem coś takiego przy probie jednego wydruku staje zaraz po tym jak skończy pomiar stołu i ma przejść do drukowania. Czytałem na githubie i na grupach octoprinta że dzieje się tak przy złym zasilaniu RPI lub kablu usb ale myślę że wyeliminowałem te dwie przyczyny bo i zasilacz i kabel podmieniłem. Ostatnio potraktowałem slicerem plik ponownie i o ile pamiętam zrobiłem ręczne poziomowanie stołu więc przychodzi mi do głowy czy przypadkiem jak stanie zaraz po pomiarze stołu nie ma to coś wspolnego z tym że procek na płycie Anet nie ogarnia danych po pomiarze ??
Awatar użytkownika
dragonn
Zasłużony
Postów w temacie: 8
Posty: 6383
Rejestracja: 12 gru 2016, 21:50
Lokalizacja: Opole
Drukarka: LUME
x 1455

Re: unhandled communication error OctoPrint

Post autor: dragonn »

Podmiana kabla USB nie oznacza że rozwiąże to problem. Po tym jak wywali ten błąd zaloguj się po ssh i wpisz polecenie:

Kod: Zaznacz cały

dmesg | tail
Uwaga jak polecenie nie wejdzie to masz literówkę! Wynik polecenia wrzuć tutaj na forum.
StudioKamar
Konto z ograniczeniami
Postów w temacie: 16
Posty: 207
Rejestracja: 14 sty 2018, 18:34
Lokalizacja: Żnin
Drukarka: Anet A8
x 10

Re: unhandled communication error OctoPrint

Post autor: StudioKamar »

No dobra zobacze. wyeksportowałem ponownie gcode ze slicera i przeszło teraz drukuje. sprawdze przy kolejnym wydruku i dam znać. a Co robi to polecenie ??
Awatar użytkownika
dragonn
Zasłużony
Postów w temacie: 8
Posty: 6383
Rejestracja: 12 gru 2016, 21:50
Lokalizacja: Opole
Drukarka: LUME
x 1455

Re: unhandled communication error OctoPrint

Post autor: dragonn »

Zrzuca końcówkę logów systemowych Linuksa. Szukamy tam błędów związanych z pracą USB.
StudioKamar
Konto z ograniczeniami
Postów w temacie: 16
Posty: 207
Rejestracja: 14 sty 2018, 18:34
Lokalizacja: Żnin
Drukarka: Anet A8
x 10

Re: unhandled communication error OctoPrint

Post autor: StudioKamar »

a czyli coś o czy nie mam sinobladego pojecia. Dobra odezwę się jak tylko to ponownie się pojawi
StudioKamar
Konto z ograniczeniami
Postów w temacie: 16
Posty: 207
Rejestracja: 14 sty 2018, 18:34
Lokalizacja: Żnin
Drukarka: Anet A8
x 10

Re: unhandled communication error OctoPrint

Post autor: StudioKamar »

Kod: Zaznacz cały

 0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.28-v7+ (dc4@dc4-XPS13-9333) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611) ) #998 SMP Mon May 15 16:55:39 BST 2017
[    0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt:Machine model: Raspberry Pi 3 Model B Rev 1.2
[    0.000000] cma: Reserved 8 MiB at 0x36800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 225280
[    0.000000] free_area_init_node: node 0, pgdat 80c6edc0, node_mem_map b603a000
[    0.000000]   Normal zone: 1980 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 225280 pages, LIFO batch:31
[    0.000000] percpu: Embedded 14 pages/cpu @b5ff4000 s25600 r8192 d23552 u57344
[    0.000000] pcpu-alloc: s25600 r8192 d23552 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 223300
[    0.000000] Kernel command line: 8250.nr_uarts=0 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  dwc_otg.lpm_enable=0 console=ttyS0,115200 console=tty1 root=PARTUUID=a2303d03-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 871340K/901120K available (7168K kernel code, 483K rwdata, 2012K rodata, 1024K init, 778K bss, 21588K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xb7800000 - 0xff800000   (1152 MB)
    lowmem  : 0x80000000 - 0xb7000000   ( 880 MB)
    modules : 0x7f000000 - 0x80000000   (  16 MB)
      .text : 0x80008000 - 0x80800000   (8160 kB)
      .init : 0x80b00000 - 0x80c00000   (1024 kB)
      .data : 0x80c00000 - 0x80c78f94   ( 484 kB)
       .bss : 0x80c7a000 - 0x80d3ca64   ( 779 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000009] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000025] Switching to timer-based delay loop, resolution 52ns
[    0.000326] Console: colour dummy device 80x30
[    0.001220] console [tty1] enabled
[    0.001269] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.001339] pid_max: default: 32768 minimum: 301
[    0.001705] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001747] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002771] Disabling cpuset control group subsystem
[    0.002958] CPU: Testing write buffer coherency: ok
[    0.003029] ftrace: allocating 22386 entries in 66 pages
[    0.056074] CPU0: update cpu_capacity 1024
[    0.056141] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.056239] Setting up static identity map for 0x100000 - 0x100034
[    0.058451] CPU1: update cpu_capacity 1024
[    0.058459] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.059175] CPU2: update cpu_capacity 1024
[    0.059182] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.059850] CPU3: update cpu_capacity 1024
[    0.059856] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.059940] Brought up 4 CPUs
[    0.060112] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.060142] CPU: All CPU(s) started in HYP mode.
[    0.060169] CPU: Virtualization extensions available.
[    0.060980] devtmpfs: initialized
[    0.072032] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[    0.072356] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.072419] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.072984] pinctrl core: initialized pinctrl subsystem
[    0.073903] NET: Registered protocol family 16
[    0.076172] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.084967] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.085016] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.085189] Serial: AMBA PL011 UART driver
[    0.087076] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.087618] uart-pl011 3f201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
[    0.156684] bcm2835-dma 3f007000.dma: DMA legacy API manager at b780f000, dmachans=0x1
[    0.158546] SCSI subsystem initialized
[    0.158727] usbcore: registered new interface driver usbfs
[    0.158830] usbcore: registered new interface driver hub
[    0.158945] usbcore: registered new device driver usb
[    0.165620] raspberrypi-firmware soc:firmware: Attached to firmware from 2017-05-15 17:01
[    0.167032] clocksource: Switched to clocksource arch_sys_counter
[    0.213971] VFS: Disk quotas dquot_6.6.0
[    0.214082] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.214309] FS-Cache: Loaded
[    0.214574] CacheFiles: Loaded
[    0.226750] NET: Registered protocol family 2
[    0.227691] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.227843] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.228055] TCP: Hash tables configured (established 8192 bind 8192)
[    0.228171] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.228238] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.228473] NET: Registered protocol family 1
[    0.228912] RPC: Registered named UNIX socket transport module.
[    0.228944] RPC: Registered udp transport module.
[    0.228972] RPC: Registered tcp transport module.
[    0.229000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.229951] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[    0.232257] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    0.248316] FS-Cache: Netfs 'nfs' registered for caching
[    0.249315] NFS: Registering the id_resolver key type
[    0.249366] Key type id_resolver registered
[    0.249395] Key type id_legacy registered
[    0.251837] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.251985] io scheduler noop registered
[    0.252015] io scheduler deadline registered (default)
[    0.252341] io scheduler cfq registered
[    0.258010] BCM2708FB: allocated DMA memory f6910000
[    0.258065] BCM2708FB: allocated DMA channel 0 @ b780f000
[    0.266770] Console: switching to colour frame buffer device 82x26
[    0.275206] bcm2835-rng 3f104000.rng: hwrng registered
[    0.277618] vc-cma: Videocore CMA driver
[    0.279835] vc-cma: vc_cma_base      = 0x00000000
[    0.282057] vc-cma: vc_cma_size      = 0x00000000 (0 MiB)
[    0.284318] vc-cma: vc_cma_initial   = 0x00000000 (0 MiB)
[    0.286724] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
[    0.306269] brd: module loaded
[    0.317240] loop: module loaded
[    0.319280] Loading iSCSI transport class v2.0-870.
[    0.321826] usbcore: registered new interface driver smsc95xx
[    0.323919] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    0.552073] Core Release: 2.80a
[    0.554136] Setting default values for core params
[    0.556181] Finished setting default values for core params
[    0.758650] Using Buffer DMA mode
[    0.760698] Periodic Transfer Interrupt Enhancement - disabled
[    0.762850] Multiprocessor Interrupt Enhancement - disabled
[    0.765016] OTG VER PARAM: 0, OTG VER FLAG: 0
[    0.767228] Dedicated Tx FIFOs mode
[    0.769681] WARN::dwc_otg_hcd_init:1034: FIQ DMA bounce buffers: virt = 0xb6904000 dma = 0xf6904000 len=9024
[    0.774124] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[    0.785467] dwc_otg: Microframe scheduler enabled
[    0.785511] WARN::hcd_init_fiq:459: FIQ on core 1 at 0x8058e63c
[    0.787806] WARN::hcd_init_fiq:460: FIQ ASM at 0x8058e9ac length 36
[    0.790126] WARN::hcd_init_fiq:486: MPHI regs_base at 0xb787a000
[    0.792497] dwc_otg 3f980000.usb: DWC OTG Controller
[    0.794811] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    0.797188] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
[    0.799506] Init: Port Power? op_state=1
[    0.801756] Init: Power Port (0)
[    0.804130] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.806439] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.808756] usb usb1: Product: DWC OTG Controller
[    0.811002] usb usb1: Manufacturer: Linux 4.9.28-v7+ dwc_otg_hcd
[    0.813270] usb usb1: SerialNumber: 3f980000.usb
[    0.816337] hub 1-0:1.0: USB hub found
[    0.818571] hub 1-0:1.0: 1 port detected
[    0.821301] dwc_otg: FIQ enabled
[    0.821305] dwc_otg: NAK holdoff enabled
[    0.821309] dwc_otg: FIQ split-transaction FSM enabled
[    0.821323] Module dwc_common_port init
[    0.821559] usbcore: registered new interface driver usb-storage
[    0.823900] mousedev: PS/2 mouse device common for all mice
[    0.827058] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
[    0.829581] bcm2835-cpufreq: min=600000 max=1200000
[    0.832215] sdhci: Secure Digital Host Controller Interface driver
[    0.834528] sdhci: Copyright(c) Pierre Ossman
[    0.837070] sdhost-bcm2835 3f202000.sdhost: could not get clk, deferring probe
[    0.841637] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
[    0.844178] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.853888] ledtrig-cpu: registered to indicate activity on CPUs
[    0.856537] hidraw: raw HID events driver (C) Jiri Kosina
[    0.859198] usbcore: registered new interface driver usbhid
[    0.861661] usbhid: USB HID core driver
[    0.864899] vchiq: vchiq_init_state: slot_zero = 0xb6980000, is_master = 0
[    0.869127] Initializing XFRM netlink socket
[    0.871667] NET: Registered protocol family 17
[    0.874253] Key type dns_resolver registered
[    0.877117] Registering SWP/SWPB emulation handler
[    0.880296] registered taskstats version 1
[    0.883085] vc-sm: Videocore shared memory driver
[    0.885592] [vc_sm_connected_init]: start
[    0.888522] [vc_sm_connected_init]: end - returning 0
[    0.896874] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[    0.903266] sdhost: log_buf @ b6907000 (f6907000)
[    0.977060] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[    0.981722] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[    0.984157] mmc-bcm2835 3f300000.mmc: DMA channel allocated
[    1.037122] Indeed it is in host mode hprt0 = 00021501
[    1.099584] of_cfs_init
[    1.101918] of_cfs_init: OK
[    1.104545] Waiting for root device PARTUUID=a2303d03-02...
[    1.110377] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.116950] mmc0: new high speed SDHC card at address 59b4
[    1.119969] mmcblk0: mmc0:59b4       29.8 GiB
[    1.123732]  mmcblk0: p1 p2
[    1.126473] random: fast init done
[    1.133361] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    1.137200] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.140977] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.145919] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    1.237074] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    1.239196] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    1.239247] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.245700] Indeed it is in host mode hprt0 = 00001101
[    1.247920] devtmpfs: mounted
[    1.311856] Freeing unused kernel memory: 1024K (80b00000 - 80c00000)
[    1.312625] mmc1: new high speed SDIO card at address 0001
[    1.477367] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[    1.479893] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.483173] hub 1-1:1.0: USB hub found
[    1.485620] hub 1-1:1.0: 5 ports detected
[    1.602530] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[    1.607632] systemd[1]: Detected architecture 'arm'.
[    1.724600] NET: Registered protocol family 10
[    1.728691] systemd[1]: Inserted module 'ipv6'
[    1.732831] systemd[1]: Set hostname to <octopi>.
[    1.735603] systemd[1]: Initializing machine ID from random generator.
[    1.738526] systemd[1]: Installed transient /etc/machine-id file.
[    1.807125] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    1.947391] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[    1.949934] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.955382] smsc95xx v1.0.5
[    2.070910] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:4a:01:26
[    2.094788] systemd[1]: Cannot add dependency job for unit regenerate_ssh_host_keys.service, ignoring: Unit regenerate_ssh_host_keys.service failed to load: No such file or directory.
[    2.103379] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    2.114760] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    2.120822] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    2.167100] usb 1-1.5: new high-speed USB device number 4 using dwc_otg
[    2.437182] usb 1-1.5: New USB device found, idVendor=046d, idProduct=0819
[    2.439343] usb 1-1.5: New USB device strings: Mfr=0, Product=0, SerialNumber=2
[    2.441501] usb 1-1.5: SerialNumber: C851C1D0
[    2.678962] systemd-udevd[144]: starting version 215
[    2.956957] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[    3.203061] media: Linux media interface: v0.10
[    3.231932] Linux video capture interface: v2.00
[    3.265762] usbcore: registered new interface driver brcmfmac
[    3.393071] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    3.417157] brcmfmac: Firmware version = wl0: May 27 2016 00:13:38 version 7.45.41.26 (r640327) FWID 01-df77e4a7
[    3.843448] usb 1-1.5: set resolution quirk: cval->res = 384
[    3.844388] usbcore: registered new interface driver snd-usb-audio
[    3.844406] uvcvideo: Found UVC 1.00 device <unnamed> (046d:0819)
[    3.858849] uvcvideo 1-1.5:1.0: Entity type for entity Extension 4 was not initialized!
[    3.858872] uvcvideo 1-1.5:1.0: Entity type for entity Extension 6 was not initialized!
[    3.858883] uvcvideo 1-1.5:1.0: Entity type for entity Extension 7 was not initialized!
[    3.858895] uvcvideo 1-1.5:1.0: Entity type for entity Processing 2 was not initialized!
[    3.858906] uvcvideo 1-1.5:1.0: Entity type for entity Extension 3 was not initialized!
[    3.858917] uvcvideo 1-1.5:1.0: Entity type for entity Camera 1 was not initialized!
[    3.859550] input: UVC Camera (046d:0819) as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.0/input/input0
[    3.859736] usbcore: registered new interface driver uvcvideo
[    3.859740] USB Video Class driver (1.1.1)
[    3.915090] systemd-journald[139]: Received request to flush runtime journal from PID 1
[    4.478009] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[    4.478024] brcmfmac: power management disabled
[    4.802803] uart-pl011 3f201000.serial: no DMA platform data
[    4.879386] Adding 102396k swap on /var/swap.  Priority:-1 extents:2 across:118780k SSFS
[    5.558309] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[    5.558529] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.972318] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[    9.415724] Bluetooth: Core ver 2.22
[    9.415774] NET: Registered protocol family 31
[    9.415777] Bluetooth: HCI device and connection manager initialized
[    9.415789] Bluetooth: HCI socket layer initialized
[    9.415798] Bluetooth: L2CAP socket layer initialized
[    9.415816] Bluetooth: SCO socket layer initialized
[    9.421910] Bluetooth: HCI UART driver ver 2.3
[    9.421918] Bluetooth: HCI UART protocol H4 registered
[    9.421921] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    9.422050] Bluetooth: HCI UART protocol Broadcom registered
[    9.578868] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    9.578874] Bluetooth: BNEP filters: protocol multicast
[    9.578885] Bluetooth: BNEP socket layer initialized
[   11.914881] ip_tables: (C) 2000-2006 Netfilter Core Team
[   34.851510] random: crng init done
[  200.917456] usb 1-1.3: new full-speed USB device number 5 using dwc_otg
[  201.050660] usb 1-1.3: New USB device found, idVendor=1a86, idProduct=7523
[  201.050674] usb 1-1.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[  201.050683] usb 1-1.3: Product: USB2.0-Serial
[  202.098302] usbcore: registered new interface driver usbserial
[  202.098392] usbcore: registered new interface driver usbserial_generic
[  202.098482] usbserial: USB Serial support registered for generic
[  202.101379] usbcore: registered new interface driver ch341
[  202.101580] usbserial: USB Serial support registered for ch341-uart
[  202.101711] ch341 1-1.3:1.0: ch341-uart converter detected
[  202.106036] usb 1-1.3: ch341-uart converter now attached to ttyUSB0
cos Ci to mowi ?
Awatar użytkownika
dragonn
Zasłużony
Postów w temacie: 8
Posty: 6383
Rejestracja: 12 gru 2016, 21:50
Lokalizacja: Opole
Drukarka: LUME
x 1455

Re: unhandled communication error OctoPrint

Post autor: dragonn »

Wpisałeś samo dmesg i czy to wystąpiło po rozłączeniu? Bo ogólnie to nie widzę tego żeby USB się rozłączyło.
StudioKamar
Konto z ograniczeniami
Postów w temacie: 16
Posty: 207
Rejestracja: 14 sty 2018, 18:34
Lokalizacja: Żnin
Drukarka: Anet A8
x 10

Re: OctoPrint - "unhandled communication error"

Post autor: StudioKamar »

dmesg tail bez tej kreski bo nawet nie wiem jak ja zrobic nacisnalem prawym zeby skopiowac i zaczely sie sypac rozne linie kodu moze to przez to. zaraz jeszcze raz sproboje ten sam wydruk
StudioKamar
Konto z ograniczeniami
Postów w temacie: 16
Posty: 207
Rejestracja: 14 sty 2018, 18:34
Lokalizacja: Żnin
Drukarka: Anet A8
x 10

Re: OctoPrint - "unhandled communication error"

Post autor: StudioKamar »

no i ponownie wysypalo

Kod: Zaznacz cały

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.28-v7+ (dc4@dc4-XPS13-9333) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611) ) #998 SMP Mon May 15 16:55:39 BST 2017
[    0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt:Machine model: Raspberry Pi 3 Model B Rev 1.2
[    0.000000] cma: Reserved 8 MiB at 0x36800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 225280
[    0.000000] free_area_init_node: node 0, pgdat 80c6edc0, node_mem_map b603a000
[    0.000000]   Normal zone: 1980 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 225280 pages, LIFO batch:31
[    0.000000] percpu: Embedded 14 pages/cpu @b5ff4000 s25600 r8192 d23552 u57344
[    0.000000] pcpu-alloc: s25600 r8192 d23552 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 223300
[    0.000000] Kernel command line: 8250.nr_uarts=0 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  dwc_otg.lpm_enable=0 console=ttyS0,115200 console=tty1 root=PARTUUID=a2303d03-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 871340K/901120K available (7168K kernel code, 483K rwdata, 2012K rodata, 1024K init, 778K bss, 21588K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xb7800000 - 0xff800000   (1152 MB)
    lowmem  : 0x80000000 - 0xb7000000   ( 880 MB)
    modules : 0x7f000000 - 0x80000000   (  16 MB)
      .text : 0x80008000 - 0x80800000   (8160 kB)
      .init : 0x80b00000 - 0x80c00000   (1024 kB)
      .data : 0x80c00000 - 0x80c78f94   ( 484 kB)
       .bss : 0x80c7a000 - 0x80d3ca64   ( 779 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000009] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000025] Switching to timer-based delay loop, resolution 52ns
[    0.000326] Console: colour dummy device 80x30
[    0.001220] console [tty1] enabled
[    0.001269] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.001339] pid_max: default: 32768 minimum: 301
[    0.001705] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001747] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002771] Disabling cpuset control group subsystem
[    0.002958] CPU: Testing write buffer coherency: ok
[    0.003029] ftrace: allocating 22386 entries in 66 pages
[    0.056074] CPU0: update cpu_capacity 1024
[    0.056141] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.056239] Setting up static identity map for 0x100000 - 0x100034
[    0.058451] CPU1: update cpu_capacity 1024
[    0.058459] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.059175] CPU2: update cpu_capacity 1024
[    0.059182] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.059850] CPU3: update cpu_capacity 1024
[    0.059856] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.059940] Brought up 4 CPUs
[    0.060112] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.060142] CPU: All CPU(s) started in HYP mode.
[    0.060169] CPU: Virtualization extensions available.
[    0.060980] devtmpfs: initialized
[    0.072032] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[    0.072356] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.072419] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.072984] pinctrl core: initialized pinctrl subsystem
[    0.073903] NET: Registered protocol family 16
[    0.076172] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.084967] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.085016] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.085189] Serial: AMBA PL011 UART driver
[    0.087076] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.087618] uart-pl011 3f201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
[    0.156684] bcm2835-dma 3f007000.dma: DMA legacy API manager at b780f000, dmachans=0x1
[    0.158546] SCSI subsystem initialized
[    0.158727] usbcore: registered new interface driver usbfs
[    0.158830] usbcore: registered new interface driver hub
[    0.158945] usbcore: registered new device driver usb
[    0.165620] raspberrypi-firmware soc:firmware: Attached to firmware from 2017-05-15 17:01
[    0.167032] clocksource: Switched to clocksource arch_sys_counter
[    0.213971] VFS: Disk quotas dquot_6.6.0
[    0.214082] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.214309] FS-Cache: Loaded
[    0.214574] CacheFiles: Loaded
[    0.226750] NET: Registered protocol family 2
[    0.227691] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.227843] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.228055] TCP: Hash tables configured (established 8192 bind 8192)
[    0.228171] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.228238] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.228473] NET: Registered protocol family 1
[    0.228912] RPC: Registered named UNIX socket transport module.
[    0.228944] RPC: Registered udp transport module.
[    0.228972] RPC: Registered tcp transport module.
[    0.229000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.229951] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[    0.232257] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    0.248316] FS-Cache: Netfs 'nfs' registered for caching
[    0.249315] NFS: Registering the id_resolver key type
[    0.249366] Key type id_resolver registered
[    0.249395] Key type id_legacy registered
[    0.251837] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.251985] io scheduler noop registered
[    0.252015] io scheduler deadline registered (default)
[    0.252341] io scheduler cfq registered
[    0.258010] BCM2708FB: allocated DMA memory f6910000
[    0.258065] BCM2708FB: allocated DMA channel 0 @ b780f000
[    0.266770] Console: switching to colour frame buffer device 82x26
[    0.275206] bcm2835-rng 3f104000.rng: hwrng registered
[    0.277618] vc-cma: Videocore CMA driver
[    0.279835] vc-cma: vc_cma_base      = 0x00000000
[    0.282057] vc-cma: vc_cma_size      = 0x00000000 (0 MiB)
[    0.284318] vc-cma: vc_cma_initial   = 0x00000000 (0 MiB)
[    0.286724] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
[    0.306269] brd: module loaded
[    0.317240] loop: module loaded
[    0.319280] Loading iSCSI transport class v2.0-870.
[    0.321826] usbcore: registered new interface driver smsc95xx
[    0.323919] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    0.552073] Core Release: 2.80a
[    0.554136] Setting default values for core params
[    0.556181] Finished setting default values for core params
[    0.758650] Using Buffer DMA mode
[    0.760698] Periodic Transfer Interrupt Enhancement - disabled
[    0.762850] Multiprocessor Interrupt Enhancement - disabled
[    0.765016] OTG VER PARAM: 0, OTG VER FLAG: 0
[    0.767228] Dedicated Tx FIFOs mode
[    0.769681] WARN::dwc_otg_hcd_init:1034: FIQ DMA bounce buffers: virt = 0xb6904000 dma = 0xf6904000 len=9024
[    0.774124] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[    0.785467] dwc_otg: Microframe scheduler enabled
[    0.785511] WARN::hcd_init_fiq:459: FIQ on core 1 at 0x8058e63c
[    0.787806] WARN::hcd_init_fiq:460: FIQ ASM at 0x8058e9ac length 36
[    0.790126] WARN::hcd_init_fiq:486: MPHI regs_base at 0xb787a000
[    0.792497] dwc_otg 3f980000.usb: DWC OTG Controller
[    0.794811] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    0.797188] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
[    0.799506] Init: Port Power? op_state=1
[    0.801756] Init: Power Port (0)
[    0.804130] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.806439] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.808756] usb usb1: Product: DWC OTG Controller
[    0.811002] usb usb1: Manufacturer: Linux 4.9.28-v7+ dwc_otg_hcd
[    0.813270] usb usb1: SerialNumber: 3f980000.usb
[    0.816337] hub 1-0:1.0: USB hub found
[    0.818571] hub 1-0:1.0: 1 port detected
[    0.821301] dwc_otg: FIQ enabled
[    0.821305] dwc_otg: NAK holdoff enabled
[    0.821309] dwc_otg: FIQ split-transaction FSM enabled
[    0.821323] Module dwc_common_port init
[    0.821559] usbcore: registered new interface driver usb-storage
[    0.823900] mousedev: PS/2 mouse device common for all mice
[    0.827058] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
[    0.829581] bcm2835-cpufreq: min=600000 max=1200000
[    0.832215] sdhci: Secure Digital Host Controller Interface driver
[    0.834528] sdhci: Copyright(c) Pierre Ossman
[    0.837070] sdhost-bcm2835 3f202000.sdhost: could not get clk, deferring probe
[    0.841637] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
[    0.844178] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.853888] ledtrig-cpu: registered to indicate activity on CPUs
[    0.856537] hidraw: raw HID events driver (C) Jiri Kosina
[    0.859198] usbcore: registered new interface driver usbhid
[    0.861661] usbhid: USB HID core driver
[    0.864899] vchiq: vchiq_init_state: slot_zero = 0xb6980000, is_master = 0
[    0.869127] Initializing XFRM netlink socket
[    0.871667] NET: Registered protocol family 17
[    0.874253] Key type dns_resolver registered
[    0.877117] Registering SWP/SWPB emulation handler
[    0.880296] registered taskstats version 1
[    0.883085] vc-sm: Videocore shared memory driver
[    0.885592] [vc_sm_connected_init]: start
[    0.888522] [vc_sm_connected_init]: end - returning 0
[    0.896874] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[    0.903266] sdhost: log_buf @ b6907000 (f6907000)
[    0.977060] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[    0.981722] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[    0.984157] mmc-bcm2835 3f300000.mmc: DMA channel allocated
[    1.037122] Indeed it is in host mode hprt0 = 00021501
[    1.099584] of_cfs_init
[    1.101918] of_cfs_init: OK
[    1.104545] Waiting for root device PARTUUID=a2303d03-02...
[    1.110377] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.116950] mmc0: new high speed SDHC card at address 59b4
[    1.119969] mmcblk0: mmc0:59b4       29.8 GiB
[    1.123732]  mmcblk0: p1 p2
[    1.126473] random: fast init done
[    1.133361] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    1.137200] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.140977] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.145919] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    1.237074] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    1.239196] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    1.239247] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.245700] Indeed it is in host mode hprt0 = 00001101
[    1.247920] devtmpfs: mounted
[    1.311856] Freeing unused kernel memory: 1024K (80b00000 - 80c00000)
[    1.312625] mmc1: new high speed SDIO card at address 0001
[    1.477367] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[    1.479893] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.483173] hub 1-1:1.0: USB hub found
[    1.485620] hub 1-1:1.0: 5 ports detected
[    1.602530] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[    1.607632] systemd[1]: Detected architecture 'arm'.
[    1.724600] NET: Registered protocol family 10
[    1.728691] systemd[1]: Inserted module 'ipv6'
[    1.732831] systemd[1]: Set hostname to <octopi>.
[    1.735603] systemd[1]: Initializing machine ID from random generator.
[    1.738526] systemd[1]: Installed transient /etc/machine-id file.
[    1.807125] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    1.947391] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[    1.949934] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.955382] smsc95xx v1.0.5
[    2.070910] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:4a:01:26
[    2.094788] systemd[1]: Cannot add dependency job for unit regenerate_ssh_host_keys.service, ignoring: Unit regenerate_ssh_host_keys.service failed to load: No such file or directory.
[    2.103379] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    2.114760] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    2.120822] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    2.167100] usb 1-1.5: new high-speed USB device number 4 using dwc_otg
[    2.437182] usb 1-1.5: New USB device found, idVendor=046d, idProduct=0819
[    2.439343] usb 1-1.5: New USB device strings: Mfr=0, Product=0, SerialNumber=2
[    2.441501] usb 1-1.5: SerialNumber: C851C1D0
[    2.678962] systemd-udevd[144]: starting version 215
[    2.956957] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[    3.203061] media: Linux media interface: v0.10
[    3.231932] Linux video capture interface: v2.00
[    3.265762] usbcore: registered new interface driver brcmfmac
[    3.393071] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    3.417157] brcmfmac: Firmware version = wl0: May 27 2016 00:13:38 version 7.45.41.26 (r640327) FWID 01-df77e4a7
[    3.843448] usb 1-1.5: set resolution quirk: cval->res = 384
[    3.844388] usbcore: registered new interface driver snd-usb-audio
[    3.844406] uvcvideo: Found UVC 1.00 device <unnamed> (046d:0819)
[    3.858849] uvcvideo 1-1.5:1.0: Entity type for entity Extension 4 was not initialized!
[    3.858872] uvcvideo 1-1.5:1.0: Entity type for entity Extension 6 was not initialized!
[    3.858883] uvcvideo 1-1.5:1.0: Entity type for entity Extension 7 was not initialized!
[    3.858895] uvcvideo 1-1.5:1.0: Entity type for entity Processing 2 was not initialized!
[    3.858906] uvcvideo 1-1.5:1.0: Entity type for entity Extension 3 was not initialized!
[    3.858917] uvcvideo 1-1.5:1.0: Entity type for entity Camera 1 was not initialized!
[    3.859550] input: UVC Camera (046d:0819) as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.0/input/input0
[    3.859736] usbcore: registered new interface driver uvcvideo
[    3.859740] USB Video Class driver (1.1.1)
[    3.915090] systemd-journald[139]: Received request to flush runtime journal from PID 1
[    4.478009] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[    4.478024] brcmfmac: power management disabled
[    4.802803] uart-pl011 3f201000.serial: no DMA platform data
[    4.879386] Adding 102396k swap on /var/swap.  Priority:-1 extents:2 across:118780k SSFS
[    5.558309] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[    5.558529] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.972318] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[    9.415724] Bluetooth: Core ver 2.22
[    9.415774] NET: Registered protocol family 31
[    9.415777] Bluetooth: HCI device and connection manager initialized
[    9.415789] Bluetooth: HCI socket layer initialized
[    9.415798] Bluetooth: L2CAP socket layer initialized
[    9.415816] Bluetooth: SCO socket layer initialized
[    9.421910] Bluetooth: HCI UART driver ver 2.3
[    9.421918] Bluetooth: HCI UART protocol H4 registered
[    9.421921] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    9.422050] Bluetooth: HCI UART protocol Broadcom registered
[    9.578868] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    9.578874] Bluetooth: BNEP filters: protocol multicast
[    9.578885] Bluetooth: BNEP socket layer initialized
[   11.914881] ip_tables: (C) 2000-2006 Netfilter Core Team
[   34.851510] random: crng init done
[  200.917456] usb 1-1.3: new full-speed USB device number 5 using dwc_otg
[  201.050660] usb 1-1.3: New USB device found, idVendor=1a86, idProduct=7523
[  201.050674] usb 1-1.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[  201.050683] usb 1-1.3: Product: USB2.0-Serial
[  202.098302] usbcore: registered new interface driver usbserial
[  202.098392] usbcore: registered new interface driver usbserial_generic
[  202.098482] usbserial: USB Serial support registered for generic
[  202.101379] usbcore: registered new interface driver ch341
[  202.101580] usbserial: USB Serial support registered for ch341-uart
[  202.101711] ch341 1-1.3:1.0: ch341-uart converter detected
[  202.106036] usb 1-1.3: ch341-uart converter now attached to ttyUSB0
Awatar użytkownika
dragonn
Zasłużony
Postów w temacie: 8
Posty: 6383
Rejestracja: 12 gru 2016, 21:50
Lokalizacja: Opole
Drukarka: LUME
x 1455

Re: OctoPrint - "unhandled communication error"

Post autor: dragonn »

Restartujesz Pi po tym jak posypie?
ODPOWIEDZ

Wróć do „Firmware'y i hosty”