Znowu stanelo, tyle ze w innym miejscu
Kod: Zaznacz cały
5:48:31M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.01(RTOS) running on Duet WiFi 1.02 or later
Board ID: 08DGM-9T6BU-FG3S8-6J9DG-3S46S-TVJ3F
Used output buffers: 1 of 20 (14 max)
=== RTOS ===
Static ram: 28476
Dynamic ram: 96392 of which 16 recycled
Exception stack ram used: 428
Never used ram: 5760
Tasks: NETWORK(ready,272) HEAT(blocked,1248) MAIN(running,3548)
Owned mutexes:
=== Platform ===
Last reset 03:00:42 ago, cause: power up
Last software reset at 2019-10-22 10:50, reason: User, spinning module GCodes, available RAM 5840 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 2.7ms, max retries 0
MCU temperature: min 35.1, current 45.0, max 45.4
Supply voltage: min 11.4, current 12.6, max 12.7, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max 0/474
Driver 1: standstill, SG min/max 0/467
Driver 2: standstill, SG min/max 0/468
Driver 3: standstill, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Date/time: 2019-10-26 15:48:27
Slowest loop: 251.58ms; fastest: 0.07ms
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 120, MaxWait: 3653980ms, Underruns: 18, 0
Scheduled moves: 138950, completed moves: 138949
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.2
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X-53.272 Y19.900 E7.6444" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 182.45ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21
WiFi MAC address 80:7d:3a:15:1e:1c
WiFi Vcc 3.40, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 15880
WiFi IP address 192.168.5.110
WiFi signal strength -46dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Expansion ===
a przy probie G28, widze ze znowu tylko 1 silnik jezdzi, puscilem Emergency Stop i ujawnilo sie
Kod: Zaznacz cały
Error: Homing failed
Error: Internal Error in Seek at ../src/Storage/FileStore.cpp(218)
Cancelled printing file HalterH.gcode, print time was 1h 59m
Error: G0/G1: insufficient axes homed
Podmienie karte SD i zobacze...