Mam błąd przy BlTouch.
Konfiguracja:
Kod: Zaznacz cały
######################################################################
# "RepRapDiscount 128x64 Full Graphic Smart Controller" type displays
######################################################################
[display]
lcd_type: st7920
cs_pin: EXP1_4
sclk_pin: EXP1_5
sid_pin: EXP1_3
encoder_pins: ^EXP2_3, ^EXP2_5
click_pin: ^!EXP1_2
#kill_pin: ^!EXP2_8
[output_pin beeper]
pin: EXP1_1
# This file contains common pin mappings for RAMPS (v1.3 and later)
# boards. RAMPS boards typically use a firmware compiled for the AVR
# atmega2560 (though other AVR chips are also possible).
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: ar54
dir_pin: ar55
enable_pin: !ar38
microsteps: 16
rotation_distance: 40
endstop_pin: ^ar3
#endstop_pin: ^ar2
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_y]
step_pin: ar60
dir_pin: !ar61
enable_pin: !ar56
microsteps: 16
rotation_distance: 40
endstop_pin: ^ar14
#endstop_pin: ^ar15
position_endstop: 0
position_max: 190
homing_speed: 50
[stepper_z]
step_pin: ar46
dir_pin: ar48
enable_pin: !ar62
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
#endstop_pin: ^ar19
position_endstop: 0.5
position_max: 200
[bltouch]
sensor_pin: ^ar2
control_pin: ar11
[safe_z_home]
home_xy_position: 100,100 # Change coordinates to the center of your print bed
speed: 50
z_hop: 10 # Move up 10mm
z_hop_speed: 5
[extruder]
step_pin: ar26
dir_pin: ar28
enable_pin: !ar24
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: ar10
sensor_type: EPCOS 100K B57560G104F
sensor_pin: analog13
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 250
[heater_fan fan1]
pin: ar4
heater: extruder
heater_temp: 50
fan_speed: 1.0
#[extruder1]
#step_pin: ar36
#dir_pin: ar34
#enable_pin: !ar30
#heater_pin: ar9
#sensor_pin: analog15
#...
[heater_bed]
heater_pin: ar8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: analog14
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: ar9
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
pin_map: arduino
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
# Common EXP1 / EXP2 (display) pins
[board_pins]
aliases:
# Common EXP1 header found on many "all-in-one" ramps clones
EXP1_1=ar37, EXP1_3=ar17, EXP1_5=ar23, EXP1_7=ar27, EXP1_9=<GND>,
EXP1_2=ar35, EXP1_4=ar16, EXP1_6=ar25, EXP1_8=ar29, EXP1_10=<5V>,
# EXP2 header
EXP2_1=ar50, EXP2_3=ar31, EXP2_5=ar33, EXP2_7=ar49, EXP2_9=<GND>,
EXP2_2=ar52, EXP2_4=ar53, EXP2_6=ar51, EXP2_8=ar41, EXP2_10=<RST>
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
# Note, some boards wire: EXP2_8=<RST>, EXP2_10=ar41
# See the sample-lcd.cfg file for definitions of common LCD displays.
[virtual_sdcard]
# for gcode upload
path: ~/gcode_files
[display_status]
# for display messages in status panel
[pause_resume]
# for pause/resume functionality.
# Mainsail needs gcode macros for `PAUSE`, `RESUME` and `CANCEL_PRINT` to make the buttons work.
[gcode_macro PAUSE]
rename_existing: BASE_PAUSE
default_parameter_X: 190 #edit to your park position
default_parameter_Y: 200 #edit to your park position
default_parameter_Z: 10 #edit to your park position
default_parameter_E: 1 #edit to your retract length
gcode:
SAVE_GCODE_STATE NAME=PAUSE_state
BASE_PAUSE
G91
G1 E-{E} F2100
G1 Z{Z}
G90
G1 X{X} Y{Y} F6000
[gcode_macro RESUME]
rename_existing: BASE_RESUME
default_parameter_E: 1 #edit to your retract length
gcode:
G91
G1 E{E} F2100
G90
RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
BASE_RESUME
[gcode_macro CANCEL_PRINT]
rename_existing: BASE_CANCEL_PRINT
gcode:
TURN_OFF_HEATERS
CLEAR_PAUSE
SDCARD_RESET_FILE
BASE_CANCEL_PRINT
