MKS SBASE V1.3 + MKS TFT32

Czyli co i jak podłączyć żeby działało
Awatar użytkownika
Berg
Zasłużony
Postów w temacie: 14
Posty: 7564
Rejestracja: 05 lis 2016, 11:57
Lokalizacja: Kraków
Drukarka: Lume, K8400, HC Evo
x 2667

Re: MKS SBASE V1.3 + MKS TFT32

Post autor: Berg »

myślę, że jeszcze nikt tego nie wie.
Awatar użytkownika
zen
Postów w temacie: 5
Posty: 295
Rejestracja: 26 lut 2017, 20:53
Lokalizacja: Poznań miasto doznań
Drukarka: Too many
x 34
Kontakt:

Re: MKS SBASE V1.3 + MKS TFT32

Post autor: zen »

Mi się smoothieware automatycznie naprawiło i przestałem drukować na marlinie :(
Mendel / i3 / i3 Alu / P3Steel / HEVO^300 / Delta Kossel Linear Plus / Prusa MK3S + MMU / Voron / Bambu X1C + AMS
jarn
Postów w temacie: 4
Posty: 200
Rejestracja: 06 maja 2017, 00:13
Lokalizacja: Strzelno
Drukarka: Delta, HevORT
x 37

Re: MKS SBASE V1.3 + MKS TFT32

Post autor: jarn »

Czyli nie ma co kombinować tylko opanować config.txt.
jaca_76
Konto z ograniczeniami
Postów w temacie: 2
Posty: 66
Rejestracja: 29 lis 2017, 23:28
x 13

Re: MKS SBASE V1.3 + MKS TFT32

Post autor: jaca_76 »

Witam. Po dziele się tylko swoim małym doświadczeniem . Mam MKS SBASE i MKS TFT i za cholerę nie mogłem uruchomić komunikacji. W configu dla MKS SBASE uart0 baud rate ustawiony na 115 200 i tak samo ustawiałem dla wyświetlacza. Jako że nic nie działało postanowiłem pobawić się ustawieniami UART dla MKS TFT i jako pierwszy na próbę ustawiłem 9600 i to był strzał w 10. Zgaduje że powinna gdzieś być konfiguracja dla drugiego UARTA i a skoro jej nie ma to domyślnie jest 9600 (w configu włączyłem również 2 uart).

Jak powinno to wyglądać prawidłowo.
Awatar użytkownika
zen
Postów w temacie: 5
Posty: 295
Rejestracja: 26 lut 2017, 20:53
Lokalizacja: Poznań miasto doznań
Drukarka: Too many
x 34
Kontakt:

Re: RE: Re: MKS SBASE V1.3 + MKS TFT32

Post autor: zen »

jaca_76 pisze:Witam. Po dziele się tylko swoim małym doświadczeniem . Mam MKS SBASE i MKS TFT i za cholerę nie mogłem uruchomić komunikacji. W configu dla MKS SBASE uart0 baud rate ustawiony na 115 200 i tak samo ustawiałem dla wyświetlacza. Jako że nic nie działało postanowiłem pobawić się ustawieniami UART dla MKS TFT i jako pierwszy na próbę ustawiłem 9600 i to był strzał w 10. Zgaduje że powinna gdzieś być konfiguracja dla drugiego UARTA i a skoro jej nie ma to domyślnie jest 9600 (w configu włączyłem również 2 uart).

Jak powinno to wyglądać prawidłowo.
Na przykład tak:
https://github.com/zen/zHevo
Mendel / i3 / i3 Alu / P3Steel / HEVO^300 / Delta Kossel Linear Plus / Prusa MK3S + MMU / Voron / Bambu X1C + AMS
jaca_76
Konto z ograniczeniami
Postów w temacie: 2
Posty: 66
Rejestracja: 29 lis 2017, 23:28
x 13

Re: RE: Re: MKS SBASE V1.3 + MKS TFT32

Post autor: jaca_76 »

zen pisze:
jaca_76 pisze:Witam. Po dziele się tylko swoim małym doświadczeniem . Mam MKS SBASE i MKS TFT i za cholerę nie mogłem uruchomić komunikacji. W configu dla MKS SBASE uart0 baud rate ustawiony na 115 200 i tak samo ustawiałem dla wyświetlacza. Jako że nic nie działało postanowiłem pobawić się ustawieniami UART dla MKS TFT i jako pierwszy na próbę ustawiłem 9600 i to był strzał w 10. Zgaduje że powinna gdzieś być konfiguracja dla drugiego UARTA i a skoro jej nie ma to domyślnie jest 9600 (w configu włączyłem również 2 uart).

Jak powinno to wyglądać prawidłowo.
Na przykład tak:
https://github.com/zen/zHevo
No tak. Tylko że u mnie tak to nie działa mam:
uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port

second_usb_serial_enable true # This enables a second USB serial port

A dla wyświetlacza musiałem dać żeby działało:
#baud rate (9600:1; 57600:2; 115200:3; 250000:4)
>cfg_baud_rate:1

Hmm. Chyba że plik z plikiem config jest coś nie tak.
$A$F
Postów w temacie: 3
Posty: 147
Rejestracja: 16 sie 2017, 13:44
x 34

Re: MKS SBASE V1.3 + MKS TFT32

Post autor: $A$F »

Mam prośbę, niby mks chodzi bo mogę wbić się na niego przez lan, nowe firmware udało się do niego wgrać zamienił firmware.bin na firmware.cur, do wyświetlacza też no FW został wgrany i nic nie działa. Nie kręci silnikami nie grzeje, nie odczytuje żadnej temperatury.
Oto config txt:

Kod: Zaznacz cały

# NOTE Lines must not exceed 132 characters
# Robot module configurations : general handling of movement G-codes and slicing into moves
default_feed_rate                            4000             # Default rate ( mm/minute ) for G1/G2/G3 moves
default_seek_rate                            4000             # Default rate ( mm/minute ) for G0 moves
mm_per_arc_segment                           0.5              # Arcs are cut into segments ( lines ), this is the length for
                                                              # these segments.  Smaller values mean more resolution,
                                                              # higher values mean faster computation
mm_per_line_segment                          5                # Lines can be cut into segments ( not usefull with cartesian
                                                              # coordinates robots ).

# Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
alpha_steps_per_mm                           78.7402               # Steps per mm for alpha stepper
beta_steps_per_mm                            78.7402               # Steps per mm for beta stepper
gamma_steps_per_mm                           1649.48             # Steps per mm for gamma stepper

# Planner module configuration : Look-ahead and acceleration configuration
planner_queue_size                           32               # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING
acceleration                                 800             # Acceleration in mm/second/second.
z_acceleration                              60              # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
acceleration_ticks_per_second                1000             # Number of times per second the speed is updated
junction_deviation                           0.02             # Similar to the old "max_jerk", in millimeters,
                                                              # see https://github.com/grbl/grbl/blob/master/planner.c
                                                              # and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8
                                                              # Lower values mean being more careful, higher values means being
                                                              # faster and have more jerk
#z_junction_deviation                        0.0              # for Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
#minimum_planner_speed                       0.0              # sets the minimum planner speed in mm/sec





# Stepper module configuration
microseconds_per_step_pulse                  1                # Duration of step pulses to stepper drivers, in microseconds
base_stepping_frequency                      100000           # Base frequency for stepping, higher gives smoother movement

# Cartesian axis speed limits
x_axis_max_speed                             4200            # mm/min
y_axis_max_speed                             4200            # mm/min
z_axis_max_speed                             200              # mm/min

# Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
alpha_step_pin                               2.0              # Pin for alpha stepper step signal
alpha_dir_pin                                0.5!              # Pin for alpha stepper direction
alpha_en_pin                                 0.4              # Pin for alpha enable pin
alpha_current                                0.8             # X stepper motor current
alpha_max_rate                               4200.0          # mm/min

beta_step_pin                                2.1              # Pin for beta stepper step signal
beta_dir_pin                                 0.11             # Pin for beta stepper direction
beta_en_pin                                  0.10             # Pin for beta enable
beta_current                                 1.2             # Y stepper motor current
beta_max_rate                                4200.0          # mm/min

gamma_step_pin                               2.2              # Pin for gamma stepper step signal
gamma_dir_pin                                0.20!             # Pin for gamma stepper direction
gamma_en_pin                                 0.19             # Pin for gamma enable
gamma_current                                1.0              # Z stepper motor current
gamma_max_rate                               100.0            # mm/min

# Serial communications configuration ( baud rate default to 9600 if undefined )
uart0.baud_rate                              9600           # Baud rate for the default hardware serial port
second_usb_serial_enable                     true            # This enables a second usb serial port (to have both pronterface
                                                              # and a terminal connected)
#leds_disable                                true             # disable using leds after config loaded
#play_led_disable                            true             # disable the play led
pause_button_enable                          true             # Pause button enable
#pause_button_pin                            2.12             # pause button pin. default is P2.12
#kill_button_enable                           false            # set to true to enable a kill button
#kill_button_pin                              2.12             # kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
#msd_disable                                 false            # disable the MSD (USB SDCARD) when set to true (needs special binary)
#dfu_enable                                  false            # for linux developers, set to true to enable DFU

# Extruder module configuration
extruder.hotend.enable                          true             # Whether to activate the extruder module at all. All configuration is ignored if false
extruder.hotend.steps_per_mm                    427              # Steps per mm for extruder stepper
extruder.hotend.default_feed_rate               600              # Default rate ( mm/minute ) for moves where only the extruder moves
extruder.hotend.acceleration                    500              # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
extruder.hotend.max_speed                       50               # mm/s

extruder.hotend.step_pin                        2.3              # Pin for extruder step signal
extruder.hotend.dir_pin                         0.22!             # Pin for extruder dir signal
extruder.hotend.en_pin                          0.21             # Pin for extruder enable signal

# extruder offset
#extruder.hotend.x_offset                        0                # x offset from origin in mm
#extruder.hotend.y_offset                        0                # y offset from origin in mm
#extruder.hotend.z_offset                        0                # z offset from origin in mm

# firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
#extruder.hotend.retract_length                  3               # retract length in mm
#extruder.hotend.retract_feedrate                45              # retract feedrate in mm/sec
#extruder.hotend.retract_recover_length          0               # additional length for recover
#extruder.hotend.retract_recover_feedrate        8               # recover feedrate in mm/sec (should be less than retract feedrate)
#extruder.hotend.retract_zlift_length            0               # zlift on retract in mm, 0 disables
#extruder.hotend.retract_zlift_feedrate          6000            # zlift feedrate in mm/min (Note mm/min NOT mm/sec)

delta_current                                0.8              # First extruder stepper motor current

# Second extruder module configuration
#extruder.hotend2.enable                          true             # Whether to activate the extruder module at all. All configuration is ignored if false
#extruder.hotend2.steps_per_mm                    140              # Steps per mm for extruder stepper
#extruder.hotend2.default_feed_rate               600              # Default rate ( mm/minute ) for moves where only the extruder moves
#extruder.hotend2.acceleration                    500              # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
#extruder.hotend2.max_speed                       50               # mm/s

#extruder.hotend2.step_pin                        2.8              # Pin for extruder step signal
#extruder.hotend2.dir_pin                         2.13             # Pin for extruder dir signal
#extruder.hotend2.en_pin                          4.29             # Pin for extruder enable signal

#extruder.hotend2.x_offset                        0                # x offset from origin in mm
#extruder.hotend2.y_offset                        25.0             # y offset from origin in mm
#extruder.hotend2.z_offset                        0                # z offset from origin in mm
#epsilon_current                              1.5              # Second extruder stepper motor current


# Laser module configuration
laser_module_enable                          false            # Whether to activate the laser module at all. All configuration is
                                                              # ignored if false.
#laser_module_pin                             2.5             # this pin will be PWMed to control the laser. Only P2.0 - P2.5, P1.18, P1.20, P1.21, P1.23, P1.24, P1.26, P3.25, P3.26
                                                              # can be used since laser requires hardware PWM
#laser_module_max_power                       0.8             # this is the maximum duty cycle that will be applied to the laser
#laser_module_tickle_power                    0.0             # this duty cycle will be used for travel moves to keep the laser
                                                              # active without actually burning
#laser_module_pwm_period                      20              # this sets the pwm frequency as the period in microseconds

# Hotend temperature control configuration
temperature_control.hotend.enable            true             # Whether to activate this ( "hotend" ) module at all.
                                                              # All configuration is ignored if false.
temperature_control.hotend.thermistor_pin    0.24             # Pin for the thermistor to read
temperature_control.hotend.heater_pin        2.7              # Pin that controls the heater, set to nc if a readonly thermistor is being defined   2.7
temperature_control.hotend.thermistor        EPCOS100K      # see http://smoothieware.org/temperaturecontrol#toc5
#temperature_control.hotend.beta             3960             # or set the beta value
temperature_control.hotend.set_m_code        104              #
temperature_control.hotend.set_and_wait_m_code 109            #
temperature_control.hotend.designator        T                #

#temperature_control.hotend.p_factor         13.7             # permanently set the PID values after an auto pid
#temperature_control.hotend.i_factor         0.097            #
#temperature_control.hotend.d_factor         24               #

#temperature_control.hotend.max_pwm          255               # max pwm, 64 is a good value if driving a 12v resistor with 24v.

# Hotend2 temperature control configuration
#temperature_control.hotend2.enable            true             # Whether to activate this ( "hotend" ) module at all.
                                                              # All configuration is ignored if false.

#temperature_control.hotend2.thermistor_pin    0.25             # Pin for the thermistor to read
#temperature_control.hotend2.heater_pin        2.6             # Pin that controls the heater
#temperature_control.hotend2.thermistor        EPCOS100K        # see http://smoothieware.org/temperaturecontrol#toc5
##temperature_control.hotend2.beta             4066             # or set the beta value
#temperature_control.hotend2.set_m_code        884              #
#temperature_control.hotend2.set_and_wait_m_code 889            #
#temperature_control.hotend2.designator        T1               #

#temperature_control.hotend2.p_factor          13.7           # permanently set the PID values after an auto pid
#temperature_control.hotend2.i_factor          0.097          #
#temperature_control.hotend2.d_factor          24             #

#temperature_control.hotend2.max_pwm          64               # max pwm, 64 is a good value if driving a 12v resistor with 24v.

temperature_control.bed.enable               true             #
temperature_control.bed.thermistor_pin       0.23             #
temperature_control.bed.heater_pin           2.5              #  2.5
temperature_control.bed.thermistor           EPCOS100K    # see http://smoothieware.org/temperaturecontrol#toc5
#temperature_control.bed.beta                3960             # or set the beta value

temperature_control.bed.set_m_code           140              #
temperature_control.bed.set_and_wait_m_code  190              #
temperature_control.bed.designator           B                #

#temperature_control.bed.bang_bang            false           # set to true to use bang bang control rather than PID
#temperature_control.bed.hysteresis           2.0             # set to the temperature in degrees C to use as hysteresis
                                                              # when using bang bang

# Switch module for fan control
switch.fan.enable                            true             #
switch.fan.input_on_command                  M106             #
switch.fan.input_off_command                 M107             #
switch.fan.output_pin                        2.4              #
switch.fan.output_type                       pwm              # pwm output settable with S parameter in the input_on_comand
#switch.fan.max_pwm                           255              # set max pwm for the pin default is 255

#switch.misc.enable                           true             #
#switch.misc.input_on_command                 M42              #
#switch.misc.input_off_command                M43              #
#switch.misc.output_pin                       2.4              #
#switch.misc.output_type                      digital          # just an on or off pin

# automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
# useful to turn on a fan or water pump to cool the hotend
#temperatureswitch.hotend.enable	            true             #
#temperatureswitch.hotend.designator          T                # first character of the temperature control designator to use as the temperature sensor to monitor
#temperatureswitch.hotend.switch              misc             # select which switch to use, matches the name of the defined switch
#temperatureswitch.hotend.threshold_temp      60.0             # temperature to turn on (if rising) or off the switch
#temperatureswitch.hotend.heatup_poll         15               # poll heatup at 15 sec intervals
#temperatureswitch.hotend.cooldown_poll       60               # poll cooldown at 60 sec intervals

# Switch module for spindle control
#switch.spindle.enable                        false            #

# Endstops
endstops_enable                              true             # the endstop module is enabled by default and can be disabled here
#corexy_homing                               false            # set to true if homing on a hbit or corexy
alpha_min_endstop                            1.24^!            # add a ! to invert if endstop is NO connected to ground
alpha_max_endstop                            1.25^            # NOTE set to nc if this is not installed
alpha_homing_direction                       home_to_min      # or set to home_to_max and set alpha_max
alpha_min                                    0                # this gets loaded after homing when home_to_min is set
alpha_max                                    210             # this gets loaded after homing when home_to_max is set
beta_min_endstop                             1.26^!            #
beta_max_endstop                             1.27^            #
beta_homing_direction                        home_to_min      #
beta_min                                     0                #
beta_max                                     210             #
gamma_min_endstop                            1.28^!            #
gamma_max_endstop                            1.29^            #
gamma_homing_direction                       home_to_min      #
gamma_min                                    0                #
gamma_max                                    120              #

# optional order in which axis will home, default is they all home at the same time,
# if this is set it will force each axis to home one at a time in the specified order
#homing_order                                 XYZ              # x axis followed by y then z last

# optional enable limit switches, actions will stop if any enabled limit switch is triggered
#alpha_limit_enable                          false            # set to true to enable X min and max limit switches
#beta_limit_enable                           false            # set to true to enable Y min and max limit switches
#gamma_limit_enable                          false            # set to true to enable Z min and max limit switches

alpha_fast_homing_rate_mm_s                  50               # feedrates in mm/second
beta_fast_homing_rate_mm_s                   50               # "
gamma_fast_homing_rate_mm_s                  4                # "
alpha_slow_homing_rate_mm_s                  25               # "
beta_slow_homing_rate_mm_s                   25               # "
gamma_slow_homing_rate_mm_s                  2                # "

alpha_homing_retract_mm                      5                # distance in mm
beta_homing_retract_mm                       5                # "
gamma_homing_retract_mm                      1                # "

#endstop_debounce_count                       100              # uncomment if you get noise on your endstops, default is 100

# optional Z probe
zprobe.enable                                false           # set to true to enable a zprobe
zprobe.probe_pin                             1.28!^          # pin probe is attached to if NC remove the !
zprobe.slow_feedrate                         5               # mm/sec probe feed rate
#zprobe.debounce_count                       100             # set if noisy
zprobe.fast_feedrate                         100             # move feedrate mm/sec
zprobe.probe_height                          5               # how much above bed to start probe
#gamma_min_endstop                           nc              # normally 1.28. Change to nc to prevent conflict,

# associated with zprobe the leveling strategy to use
#leveling-strategy.three-point-leveling.enable         true        # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
#leveling-strategy.three-point-leveling.point1         100.0,0.0   # the first probe point (x,y) optional may be defined with M557
#leveling-strategy.three-point-leveling.point2         200.0,200.0 # the second probe point (x,y)
#leveling-strategy.three-point-leveling.point3         0.0,200.0   # the third probe point (x,y)
#leveling-strategy.three-point-leveling.home_first     true        # home the XY axis before probing
#leveling-strategy.three-point-leveling.tolerance      0.03        # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
#leveling-strategy.three-point-leveling.probe_offsets  0,0,0       # the probe offsets from nozzle, must be x,y,z, default is no offset
#leveling-strategy.three-point-leveling.save_plane     false       # set to true to allow the bed plane to be saved with M500 default is false

# Panel
panel.enable                                 true             # set to true to enable the panel code
#panel.lcd                                    smoothiepanel     # set type of panel
#panel.encoder_a_pin                          3.25!^            # encoder pin
#panel.encoder_b_pin                          3.26!^            # encoder pin

# Example for reprap discount GLCD
# on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
# +5v is EXP1 pin 10, Gnd is EXP1 pin 9
panel.lcd                                   reprap_discount_glcd     #
panel.spi_channel                           0                 # spi channel to use  ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
panel.spi_cs_pin                            0.16              # spi chip select     ; GLCD EXP1 Pin 4
panel.encoder_a_pin                         3.25!^            # encoder pin         ; GLCD EXP2 Pin 3
panel.encoder_b_pin                         3.26!^            # encoder pin         ; GLCD EXP2 Pin 5
panel.click_button_pin                      1.30!^            # click button        ; GLCD EXP1 Pin 2
panel.buzz_pin                              1.31              # pin for buzzer      ; GLCD EXP1 Pin 1
panel.back_button_pin                       2.11!^            # back button         ; GLCD EXP2 Pin 8
panel.external_sd                     true              # set to true if there is an extrernal sdcard on the panel
panel.external_sd.spi_channel         1                 # set spi channel the sdcard is on
panel.external_sd.spi_cs_pin          0.28              # set spi chip select for the sdcard (or any spare pin)
panel.external_sd.sdcd_pin            0.27!^            # sd detect signal (set to nc if no sdcard detect) (or any spare pin)



# pins used with other panels
#panel.up_button_pin                         0.1!              # up button if used
#panel.down_button_pin                       0.0!              # down button if used
#panel.click_button_pin                      0.18!             # click button if used

panel.menu_offset                            0                 # some panels will need 1 here

panel.alpha_jog_feedrate                     6000              # x jogging feedrate in mm/min
panel.beta_jog_feedrate                      6000              # y jogging feedrate in mm/min
panel.gamma_jog_feedrate                     200               # z jogging feedrate in mm/min

panel.hotend_temperature                     185               # temp to set hotend when preheat is selected
panel.bed_temperature                        60                # temp to set bed when preheat is selected

# Example of a custom menu entry, which will show up in the Custom entry.
# NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
custom_menu.power_on.enable                true              #
custom_menu.power_on.name                  Power_on          #
custom_menu.power_on.command               M80               #

custom_menu.power_off.enable               true              #
custom_menu.power_off.name                 Power_off         #
custom_menu.power_off.command              M81               #

# Only needed on a smoothieboard
currentcontrol_module_enable                  true             #


return_error_on_unhandled_gcode              false            #

# network settings
network.enable                               true            # enable the ethernet network services
network.webserver.enable                     true             # enable the webserver
network.telnet.enable                        true             # enable the telnet server
#network.ip_address                           auto             # use dhcp to get ip address
# uncomment the 3 below to manually setup ip address
network.ip_address                           192.168.1.126    # the IP address
network.ip_mask                              255.255.255.0    # the ip mask
network.ip_gateway                           192.168.1.1      # the gateway address
#network.mac_override                         xx.xx.xx.xx.xx.xx  # override the mac address, only do this if you have a conflict

Może dojrzycie jakiś błąd, który robię.
P.s. drukarka to Tevo Tarantula .
jarn
Postów w temacie: 4
Posty: 200
Rejestracja: 06 maja 2017, 00:13
Lokalizacja: Strzelno
Drukarka: Delta, HevORT
x 37

Re: MKS SBASE V1.3 + MKS TFT32

Post autor: jarn »

Połącz się przez Pronterface i sprawdź odczyty temp, endstopy, silniki.
$A$F
Postów w temacie: 3
Posty: 147
Rejestracja: 16 sie 2017, 13:44
x 34

Re: MKS SBASE V1.3 + MKS TFT32

Post autor: $A$F »

jarn pisze:Połącz się przez Pronterface i sprawdź odczyty temp, endstopy, silniki.
Pod pronterface ruszyło coś. Okazuje się że wtyczki do silników mają inną pinologię niż mks base1.4(A:B:B1:A1 vs A:A1:B:B1)
Jak uruchomić PF pod mintem 18

Kod: Zaznacz cały

sudo add-apt-repository ppa:deadsnakes/ppa
sudo apt-get update  
apt-get install python3-pip

pip3 install wheel setuptools
pip3 install requests bs4
pip3 install wxpython
No i potem uruchamiamy PF z uprawnieniami administratora, Jak ktoś chce żeby było ładnie to jeszcze trzeba utworzyć regułkę UDEV i wtedy bez konta roota się uruchomi.
$A$F
Postów w temacie: 3
Posty: 147
Rejestracja: 16 sie 2017, 13:44
x 34

Re: RE: Re: MKS SBASE V1.3 + MKS TFT32

Post autor: $A$F »

$A$F pisze:
jarn pisze:Połącz się przez Pronterface i sprawdź odczyty temp, endstopy, silniki.
Pod pronterface ruszyło coś. Okazuje się że wtyczki do silników mają inną pinologię niż mks base1.4(A:B:B1:A1 vs A:A1:B:B1)
Jak uruchomić PF pod mintem 18

Kod: Zaznacz cały

sudo add-apt-repository ppa:deadsnakes/ppa
sudo apt-get update  
apt-get install python3-pip

pip3 install wheel setuptools
pip3 install requests bs4
pip3 install wxpython
No i potem uruchamiamy PF z uprawnieniami administratora, Jak ktoś chce żeby było ładnie to jeszcze trzeba utworzyć regułkę UDEV i wtedy bez konta roota się uruchomi.
Z wtyczkami nic nie kombinować. Mają jednak taką samą pinologię.

Wysłane z mojego XT1572 przy użyciu Tapatalka
ODPOWIEDZ

Wróć do „Elektronika sterująca, wyświetlacze”