Mam problem z którym nie mogę sobie poradzić
Chcę wydrukować model:
https://www.thingiverse.com/thing:989153
konwertuję plik w Cura jednak po wczytaniu nie rusza drukowanie. Po dłuższej chwili mam informację że druk zakończony a nic się nie stało.
Początek kodu:
Kod: Zaznacz cały
;FLAVOR:Marlin
;TIME:9463
;Filament used: 9.51254m
;Layer height: 0.2
;Generated with Cura_SteamEngine 3.2.1
M190 S60
M104 S200
M109 S200
M82 ;absolute extrusion mode
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F120 ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F200 E3 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
G1 F120
M117 Printing...
G5
;LAYER_COUNT:160
;LAYER:0
M107
G0 F3600 X78.763 Y42.452 Z0.3
Kod: Zaznacz cały
;TIME_ELAPSED:9463.326158
G1 F1500 E1193.40034
M107
M104 S0 ; turn off extruder
M140 S0 ; turn off bed
M84 ; disable motors
M107
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle
to release some of the pressure
G1 Z+0.5 E-5 ;X-20 Y-20 F120 ;move Z up a bit and retract filament even more
G28 X0 ;Y0 ;move X/Y to min endstops
so the head is out of the way
G1 Y180 F2000
M84 ;steppers off
G90
M300 P300 S4000
M82 ;absolute extrusion mode
M104 S0
;End of Gcode
;SETTING_3 {"extruder_quality": ["[general]\\nversion = 2\\nname = Moje ustawien
;SETTING_3 ia\\ndefinition = anycubic_i3_mega\\n\\n[metadata]\\nsetting_version
;SETTING_3 = 4\\nextruder = fdmextruder\\ntype = quality_changes\\nquality_type
;SETTING_3 = not_supported\\n\\n[values]\\nbrim_line_count = 8\\nbrim_width = 2\
;SETTING_3 \nraft_airgap = 0.1\\nraft_margin = 2\\nraft_smoothing = 3\\nretract_
;SETTING_3 at_layer_change = True\\nretraction_amount = 4\\nskirt_line_count = 2
;SETTING_3 \\nspeed_infill = 50\\nspeed_print = 50\\nspeed_wall = 50\\nspeed_wal
;SETTING_3 l_x = 40\\nsupport_pattern = lines\\n\\n"], "global_quality": "[gener
;SETTING_3 al]\\nversion = 2\\nname = Moje ustawienia\\ndefinition = anycubic_i3
;SETTING_3 _mega\\n\\n[metadata]\\nsetting_version = 4\\ntype = quality_changes\
;SETTING_3 \nquality_type = not_supported\\n\\n[values]\\nadhesion_type = skirt\
;SETTING_3 \nlayer_height = 0.2\\nsupport_type = buildplate\\n\\n"}
Z góry dziękuje