Ender 5 plus, zaczyna śladem od środka

[Jarewa]

Czy ja wiem czy to sporo. Ja mam chyba 12cm na purge line aby nie przejmować się resztkami filamentu który mam w dyszy. Prusa MMU2S ma jeszcze więcej. IMO 2 cm to minimum które ja bym ustawił

Tylko weź pod uwagę że gcode końcowy nie wyciąga. Czyli defakto dysza jest pełna plus te 20mm dodatkowo.

[Pjoter]

No nadal, wszystko to kwestia czego oczekujesz - ja lubię likwidować potencjalny problem w postaci "zapomniałem przepchnąć te 10cm filamentu jak wymieniałem szpulę i teraz dół wydruku ma inny kolor/inny materiał". Jak dasz odpowiednią prędkość to to nie jest dużo. Nie pamiętam ile ja mam ale tuż pod limitem przeskakiwania radełka.

[TomekToJa]

Już wrzucam:

Ender 3v2

Kod: Zaznacz cały

; generated by PrusaSlicer 2.4.2+win64 on 2022-05-18 at 05:29:23 UTC

; 

; external perimeters extrusion width = 0.45mm
; perimeters extrusion width = 0.45mm
; infill extrusion width = 0.45mm
; solid infill extrusion width = 0.45mm
; top infill extrusion width = 0.40mm
; first layer extrusion width = 0.42mm

M107
;TYPE:Custom
G90 ; use absolute coordinates
M83 ; extruder relative mode
M140 S40 ; set final bed temp
M104 S150 ; set temporary nozzle temp to prevent oozing during homing
G4 S10 ; allow partial nozzle warmup
G28 ; home all axis
G1 Z50 F240
G1 X2 Y10 F3000
M104 S210 ; set final nozzle temp
M190 S40 ; wait for bed temp to stabilize
M109 S210 ; wait for nozzle temp to stabilize
G1 Z0.28 F240
G92 E0
G1 Y140 E10 F1500 ; prime the nozzle
G1 X2.3 F5000
G92 E0
G1 Y10 E10 F1200 ; prime the nozzle
G92 E0
G21 ; set units to millimeters
G90 ; use absolute coordinates
M83 ; use relative distances for extrusion
; Filament gcode
M107
;LAYER_CHANGE
;Z:0.2
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0
;0.2


G1 E-5 F3600
G1 Z.2 F9000
;AFTER_LAYER_CHANGE
;0.2
G1 X82.773 Y99.245
G1 E5 F2400
M204 S500
;TYPE:Skirt/Brim
;WIDTH:0.42
G1 F1094
G1 X84.222 Y98.315 E.05397
G1 X85.471 Y98.101 E.03973
G1 X129.194 Y98.101 E1.37092
G1 X130.87 Y98.496 E.05397
G1 X132.193 Y99.597 E.05397
G1 X132.949 Y101.855 E.07467
G1 X132.949 Y102.646 E.02479
G1 X132.554 Y104.322 E.05397
G1 X131.453 Y105.645 E.05397
G1 X129.408 Y106.394 E.06827
G1 X86.475 Y108.845 E1.34832
G1 X83.099 Y108.851 E.10587
G1 X81.423 Y108.457 E.05397
G1 X80.1 Y107.356 E.05397
G1 X79.345 Y105.097 E.07467
G1 X79.345 Y104.307 E.02479
G1 X79.739 Y102.631 E.05397
G1 X80.401 Y101.696 E.03592
G1 X82.731 Y99.288 E.10506
G1 X83.002 Y99.55 F9000
G1 F1094
G1 X83.044 Y99.507 E.00188
G1 X84.428 Y98.643 E.05115
G1 X85.471 Y98.478 E.0331
G1 X129.194 Y98.478 E1.37092
G1 X130.778 Y98.872 E.05115
G1 X131.991 Y99.963 E.05115
G1 X132.571 Y101.855 E.06207
G1 X132.571 Y102.646 E.02479
G1 X132.177 Y104.229 E.05115
G1 X131.087 Y105.443 E.05115
G1 X129.387 Y106.018 E.05627
G1 X86.454 Y108.469 E1.34832
G1 X83.099 Y108.474 E.1052
G1 X81.516 Y108.08 E.05115
G1 X80.302 Y106.99 E.05115
G1 X79.722 Y105.097 E.06207
G1 X79.722 Y104.307 E.02479
G1 X80.116 Y102.723 E.05115
G1 X80.672 Y101.958 E.02966
G1 X82.961 Y99.593 E.10318
G1 E-3.5 F3600
;WIPE_START
G1 F7200
G1 X83.044 Y99.507 E-.057
G1 X84.428 Y98.643 E-.77494
G1 X85.471 Y98.478 E-.50141
G1 X85.664 Y98.478 E-.09164
;WIPE_END
G1 E-.075 F3600
G1 X85.718 Y102.103 F9000
G1 E5 F2400
;TYPE:External perimeter
G1 F1094
G1 X86.47 Y102.065 E.02359
G1 X128.684 Y102.065 E1.32358
G1 X128.904 Y102.095 E.00698
G1 X128.904 Y102.407 E.00977
G1 X128.681 Y102.436 E.00705
G1 X86.051 Y102.436 E1.33663
G1 X86.051 Y104.111 E.05252
G1 X86.012 Y104.848 E.02314
G1 X85.352 Y104.887 E.02074
G1 X83.566 Y104.887 E.05599
G1 X83.389 Y104.861 E.00561
G1 X83.389 Y104.544 E.00993
G1 X83.588 Y104.517 E.0063
G1 X85.681 Y104.517 E.06562
G1 X85.681 Y102.841 E.05253
G1 X85.715 Y102.163 E.02129
G1 X86.07 Y102.293 F9000
M106 S255
;LAYER_CHANGE
;Z:0.36
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;0.36


G1 E-3.5 F3600
;WIPE_START
G1 F7200
G1 X86.47 Y102.065 E-.36137
G1 X88.709 Y102.065 E-1.06363
;WIPE_END
G1 E-.075 F3600
G1 Z.36 F9000
;AFTER_LAYER_CHANGE
;0.36
M104 S205 ; set temperature
G1 X88.709 Y98.101
G1 E5 F2400
;TYPE:Skirt/Brim
G1 F1051
G1 X129.194 Y98.101 E1.03863
G1 X130.87 Y98.496 E.04416
G1 X132.193 Y99.597 E.04416
G1 X132.949 Y101.855 E.06109
G1 X132.949 Y102.646 E.02028
G1 X132.554 Y104.322 E.04416
G1 X131.453 Y105.645 E.04416
G1 X129.408 Y106.394 E.05586
G1 X86.475 Y108.845 E1.10321
G1 X83.099 Y108.851 E.08663
G1 X81.423 Y108.457 E.04416
G1 X80.1 Y107.356 E.04416
G1 X79.345 Y105.097 E.06109
G1 X79.345 Y104.307 E.02028
G1 X79.739 Y102.631 E.04416
G1 X80.401 Y101.696 E.02939
G1 X82.773 Y99.245 E.0875
G1 X84.222 Y98.315 E.04416
G1 X85.471 Y98.101 E.03251
G1 X88.649 Y98.101 E.08154
G1 X88.649 Y98.478 F9000
G1 F1051
G1 X129.194 Y98.478 E1.04017
G1 X130.778 Y98.872 E.04185
G1 X131.991 Y99.963 E.04185
G1 X132.571 Y101.855 E.05079
G1 X132.571 Y102.646 E.02028
G1 X132.177 Y104.229 E.04185
G1 X131.087 Y105.443 E.04185
G1 X129.387 Y106.018 E.04604
G1 X86.454 Y108.469 E1.10321
G1 X83.099 Y108.474 E.08607
G1 X81.516 Y108.08 E.04185
G1 X80.302 Y106.99 E.04185
G1 X79.722 Y105.097 E.05079
G1 X79.722 Y104.307 E.02028
G1 X80.116 Y102.723 E.04185
G1 X80.672 Y101.958 E.02427
G1 X83.044 Y99.507 E.0875
G1 X84.428 Y98.643 E.04185
G1 X85.471 Y98.478 E.02708
G1 X88.589 Y98.478 E.08
G1 E-3.5 F3600
;WIPE_START
G1 F7200
G1 X91.589 Y98.478 E-1.425
;WIPE_END
G1 E-.075 F3600
G1 X86.036 Y102.421 F9000
G1 E5 F2400
;TYPE:External perimeter
;WIDTH:0.45
G1 F1051
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
;LAYER_CHANGE
;Z:0.52
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;0.52


G1 E-3.5 F3600
;WIPE_START
G1 F7200
G1 X86.036 Y104.872 E-1.1646
G1 X85.488 Y104.872 E-.2604
;WIPE_END
G1 E-.075 F3600
G1 Z.52 F9000
;AFTER_LAYER_CHANGE
;0.52
G1 X86.036 Y102.421
G1 E5 F2400
G1 F900
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
;LAYER_CHANGE
;Z:0.68
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;0.68


G1 E-3.5 F3600
;WIPE_START
G1 F7200
G1 X86.036 Y104.872 E-1.1646
G1 X85.488 Y104.872 E-.2604
;WIPE_END
G1 E-.075 F3600
G1 Z.68 F9000
;AFTER_LAYER_CHANGE
;0.68
G1 X86.036 Y102.421
G1 E5 F2400
G1 F900
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
;LAYER_CHANGE
;Z:0.84
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;0.84


G1 E-3.5 F3600
;WIPE_START
G1 F7200
G1 X86.036 Y104.872 E-1.1646
G1 X85.488 Y104.872 E-.2604
;WIPE_END
G1 E-.075 F3600
G1 Z.84 F9000
;AFTER_LAYER_CHANGE
;0.84
G1 X86.036 Y102.421
G1 E5 F2400
G1 F900
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
;LAYER_CHANGE
;Z:1
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;1


G1 E-3.5 F3600
;WIPE_START
G1 F7200
G1 X86.036 Y104.872 E-1.1646
G1 X85.488 Y104.872 E-.2604
;WIPE_END
G1 E-.075 F3600
G1 Z1 F9000
;AFTER_LAYER_CHANGE
;1
G1 X86.036 Y102.421
G1 E5 F2400
G1 F900
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
;LAYER_CHANGE
;Z:1.16
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;1.16


G1 E-3.5 F3600
;WIPE_START
G1 F7200
G1 X86.036 Y104.872 E-1.1646
G1 X85.488 Y104.872 E-.2604
;WIPE_END
G1 E-.075 F3600
G1 Z1.16 F9000
;AFTER_LAYER_CHANGE
;1.16
G1 X86.036 Y102.421
G1 E5 F2400
G1 F900
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
G1 E-3.5 F3600
;WIPE_START
G1 F7200;_WIPE
G1 X86.036 Y104.872 E-1.1646
G1 F7200;_WIPE
G1 X85.488 Y104.872 E-.2604
;WIPE_END
G1 E-.075 F3600
M107
;TYPE:Custom
; Filament-specific end gcode 
;END gcode for filament
G1 Z3.16 F600 ; Move print head up
G1 X5 Y176 F9000 ; present print
G1 Z71.16 F600 ; Move print head further up
G1 Z150 F600 ; Move print head further up
M140 S0 ; turn off heatbed
M104 S0 ; turn off temperature
M107 ; turn off fan
M84 X Y E ; disable motors
; filament used [mm] = 32.42
; filament used [cm3] = 0.08
; filament used [g] = 0.10
; filament cost = 0.00
; total filament used [g] = 0.10
; total filament cost = 0.00
; estimated printing time (normal mode) = 2m 9s

; prusaslicer_config = begin
; avoid_crossing_perimeters = 0
; avoid_crossing_perimeters_max_detour = 0
; bed_custom_model = 
; bed_custom_texture = 
; bed_shape = 5x0,215x0,215x220,5x220
; bed_temperature = 40
; before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0\n;{layer_z}\n\n
; between_objects_gcode = 
; bottom_fill_pattern = monotonic
; bottom_solid_layers = 5
; bottom_solid_min_thickness = 0
; bridge_acceleration = 250
; bridge_angle = 0
; bridge_fan_speed = 100
; bridge_flow_ratio = 0.85
; bridge_speed = 25
; brim_separation = 0
; brim_type = outer_only
; brim_width = 0
; clip_multipart_objects = 1
; color_change_gcode = M600
; compatible_printers_condition_cummulative = "printer_model=~/(ENDER|CR|SERMOON).*/ and nozzle_diameter[0]==0.4";printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
; complete_objects = 0
; cooling = 1
; cooling_tube_length = 5
; cooling_tube_retraction = 91.5
; default_acceleration = 500
; default_filament_profile = "Generic PLA @CREALITY"
; default_print_profile = 0.16mm OPTIMAL @CREALITY
; deretract_speed = 40
; disable_fan_first_layers = 1
; dont_support_bridges = 1
; draft_shield = disabled
; duplicate_distance = 6
; elefant_foot_compensation = 0.1
; end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
; end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
; ensure_vertical_shell_thickness = 1
; external_perimeter_extrusion_width = 0.45
; external_perimeter_speed = 25
; external_perimeters_first = 0
; extra_loading_move = -2
; extra_perimeters = 0
; extruder_clearance_height = 34
; extruder_clearance_radius = 47
; extruder_colour = #FCE94F
; extruder_offset = 0x0
; extrusion_axis = E
; extrusion_multiplier = 1
; extrusion_width = 0.45
; fan_always_on = 1
; fan_below_layer_time = 100
; filament_colour = #DDDDDD
; filament_cooling_final_speed = 3.4
; filament_cooling_initial_speed = 2.2
; filament_cooling_moves = 4
; filament_cost = 20
; filament_density = 1.24
; filament_diameter = 1.75
; filament_load_time = 0
; filament_loading_speed = 28
; filament_loading_speed_start = 3
; filament_max_volumetric_speed = 15
; filament_minimal_purge_on_wipe_tower = 15
; filament_notes = ""
; filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
; filament_settings_id = "Generic PLA @CREALITY"
; filament_soluble = 0
; filament_spool_weight = 0
; filament_toolchange_delay = 0
; filament_type = PLA
; filament_unload_time = 0
; filament_unloading_speed = 90
; filament_unloading_speed_start = 100
; filament_vendor = Generic
; fill_angle = 45
; fill_density = 15%
; fill_pattern = grid
; first_layer_acceleration = 0
; first_layer_acceleration_over_raft = 0
; first_layer_bed_temperature = 40
; first_layer_extrusion_width = 0.42
; first_layer_height = 0.2
; first_layer_speed = 20
; first_layer_speed_over_raft = 30
; first_layer_temperature = 210
; full_fan_speed_layer = 0
; fuzzy_skin = none
; fuzzy_skin_point_dist = 0.8
; fuzzy_skin_thickness = 0.3
; gap_fill_enabled = 1
; gap_fill_speed = 30
; gcode_comments = 0
; gcode_flavor = marlin
; gcode_label_objects = 0
; gcode_resolution = 0.0125
; gcode_substitutions = 
; high_current_on_filament_swap = 0
; host_type = octoprint
; infill_acceleration = 0
; infill_anchor = 600%
; infill_anchor_max = 50
; infill_every_layers = 1
; infill_extruder = 1
; infill_extrusion_width = 0.45
; infill_first = 0
; infill_only_where_needed = 0
; infill_overlap = 25%
; infill_speed = 50
; inherits_cummulative = "0.16mm OPTIMAL @CREALITY";"Generic PLA @CREALITY";
; interface_shells = 0
; ironing = 0
; ironing_flowrate = 15%
; ironing_spacing = 0.1
; ironing_speed = 15
; ironing_type = top
; layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
; layer_height = 0.16
; machine_limits_usage = time_estimate_only
; machine_max_acceleration_e = 5000
; machine_max_acceleration_extruding = 500
; machine_max_acceleration_retracting = 1000
; machine_max_acceleration_travel = 1500,1250
; machine_max_acceleration_x = 500
; machine_max_acceleration_y = 500
; machine_max_acceleration_z = 100
; machine_max_feedrate_e = 60
; machine_max_feedrate_x = 500
; machine_max_feedrate_y = 500
; machine_max_feedrate_z = 10
; machine_max_jerk_e = 5
; machine_max_jerk_x = 8
; machine_max_jerk_y = 8
; machine_max_jerk_z = 0.4
; machine_min_extruding_rate = 0
; machine_min_travel_rate = 0
; max_fan_speed = 100
; max_layer_height = 0.28
; max_print_height = 250
; max_print_speed = 100
; max_volumetric_speed = 0
; min_fan_speed = 100
; min_layer_height = 0.08
; min_print_speed = 15
; min_skirt_length = 4
; mmu_segmented_region_max_width = 0
; notes = 
; nozzle_diameter = 0.4
; only_retract_when_crossing_perimeters = 0
; ooze_prevention = 0
; output_filename_format = {input_filename_base}_{print_time}_{digits(layer_height,1,2)}mm_{temperature[0]}C_{filament_type[0]}_{printer_model}.gcode
; overhangs = 0
; parking_pos_retraction = 92
; pause_print_gcode = 
; perimeter_acceleration = 0
; perimeter_extruder = 1
; perimeter_extrusion_width = 0.45
; perimeter_speed = 40
; perimeters = 2
; physical_printer_settings_id = 
; post_process = 
; print_settings_id = 0.16mm OPTIMAL @CREALITY - Kopia
; printer_model = ENDER3V2
; printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_ENDER3V2\nPRINTER_HAS_BOWDEN
; printer_settings_id = Creality Ender-3 V2
; printer_technology = FFF
; printer_variant = 0.4
; printer_vendor = 
; raft_contact_distance = 0.1
; raft_expansion = 1.5
; raft_first_layer_density = 90%
; raft_first_layer_expansion = 3
; raft_layers = 0
; remaining_times = 0
; resolution = 0
; retract_before_travel = 2
; retract_before_wipe = 70%
; retract_layer_change = 1
; retract_length = 5
; retract_length_toolchange = 1
; retract_lift = 0
; retract_lift_above = 0
; retract_lift_below = 0
; retract_restart_extra = 0
; retract_restart_extra_toolchange = 0
; retract_speed = 60
; seam_position = nearest
; silent_mode = 0
; single_extruder_multi_material = 0
; single_extruder_multi_material_priming = 0
; skirt_distance = 3
; skirt_height = 2
; skirts = 1
; slice_closing_radius = 0.049
; slicing_mode = regular
; slowdown_below_layer_time = 20
; small_perimeter_speed = 25
; solid_infill_below_area = 0
; solid_infill_every_layers = 0
; solid_infill_extruder = 1
; solid_infill_extrusion_width = 0.45
; solid_infill_speed = 40
; spiral_vase = 0
; standby_temperature_delta = -5
; start_filament_gcode = "; Filament gcode\n"
; start_gcode = G90 ; use absolute coordinates\nM83 ; extruder relative mode\nM140 S{first_layer_bed_temperature[0]} ; set final bed temp\nM104 S150 ; set temporary nozzle temp to prevent oozing during homing\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\nG1 Z50 F240\nG1 X2 Y10 F3000\nM104 S{first_layer_temperature[0]} ; set final nozzle temp\nM190 S{first_layer_bed_temperature[0]} ; wait for bed temp to stabilize\nM109 S{first_layer_temperature[0]} ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0
; support_material = 0
; support_material_angle = 0
; support_material_auto = 1
; support_material_bottom_contact_distance = 0
; support_material_bottom_interface_layers = -1
; support_material_buildplate_only = 0
; support_material_closing_radius = 2
; support_material_contact_distance = 0.15
; support_material_enforce_layers = 0
; support_material_extruder = 0
; support_material_extrusion_width = 0.38
; support_material_interface_contact_loops = 0
; support_material_interface_extruder = 0
; support_material_interface_layers = 2
; support_material_interface_pattern = rectilinear
; support_material_interface_spacing = 0.2
; support_material_interface_speed = 100%
; support_material_pattern = rectilinear
; support_material_spacing = 2
; support_material_speed = 40
; support_material_style = grid
; support_material_synchronize_layers = 0
; support_material_threshold = 40
; support_material_with_sheath = 0
; support_material_xy_spacing = 60%
; temperature = 205
; template_custom_gcode = 
; thick_bridges = 0
; thin_walls = 0
; threads = 4
; thumbnails = 
; toolchange_gcode = 
; top_fill_pattern = monotonic
; top_infill_extrusion_width = 0.4
; top_solid_infill_speed = 30
; top_solid_layers = 7
; top_solid_min_thickness = 0
; travel_speed = 150
; travel_speed_z = 0
; use_firmware_retraction = 0
; use_relative_e_distances = 1
; use_volumetric_e = 0
; variable_layer_height = 1
; wipe = 1
; wipe_into_infill = 0
; wipe_into_objects = 0
; wipe_tower = 0
; wipe_tower_bridging = 10
; wipe_tower_brim_width = 2
; wipe_tower_no_sparse_layers = 0
; wipe_tower_rotation_angle = 0
; wipe_tower_width = 60
; wipe_tower_x = 170
; wipe_tower_y = 140
; wiping_volumes_extruders = 70,70
; wiping_volumes_matrix = 0
; xy_size_compensation = 0
; z_offset = 0
; prusaslicer_config = end

Endr 5 plus

Kod: Zaznacz cały

; generated by PrusaSlicer 2.4.2+win64 on 2022-05-18 at 05:30:14 UTC

; 

; external perimeters extrusion width = 0.45mm
; perimeters extrusion width = 0.45mm
; infill extrusion width = 0.45mm
; solid infill extrusion width = 0.45mm
; top infill extrusion width = 0.40mm
; first layer extrusion width = 0.42mm

M107
;TYPE:Custom
G90 ; use absolute coordinates
M83 ; extruder relative mode
M140 S40 ; set final bed temp
M104 S150 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling
M190 S40 ; wait for bed temp to stabilize
G28 ; home all axis
G29 ; auto bed levelling
G1 Z50 F240
G1 X2 Y10 F3000
M104 S210 ; set final nozzle temp
M109 S210 ; wait for nozzle temp to stabilize
G1 Z0.28 F240
G92 E0
G1 Y140 E10 F1500 ; prime the nozzle
G1 X2.3 F5000
G92 E0
G1 Y10 E10 F1200 ; prime the nozzle
G92 E0
G21 ; set units to millimeters
G90 ; use absolute coordinates
M83 ; use relative distances for extrusion
; Filament gcode
M107
;LAYER_CHANGE
;Z:0.2
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0
;0.2


G1 E-6 F3600
G1 Z.2 F9000
;AFTER_LAYER_CHANGE
;0.2
G1 X82.773 Y99.245
G1 E6 F2400
M204 S500
;TYPE:Skirt/Brim
;WIDTH:0.42
G1 F1106
G1 X84.222 Y98.315 E.05397
G1 X85.471 Y98.101 E.03973
G1 X129.194 Y98.101 E1.37092
G1 X130.87 Y98.496 E.05397
G1 X132.193 Y99.597 E.05397
G1 X132.949 Y101.855 E.07467
G1 X132.949 Y102.646 E.02479
G1 X132.554 Y104.322 E.05397
G1 X131.453 Y105.645 E.05397
G1 X129.408 Y106.394 E.06827
G1 X86.475 Y108.845 E1.34832
G1 X83.099 Y108.851 E.10587
G1 X81.423 Y108.457 E.05397
G1 X80.1 Y107.356 E.05397
G1 X79.345 Y105.097 E.07467
G1 X79.345 Y104.307 E.02479
G1 X79.739 Y102.631 E.05397
G1 X80.401 Y101.696 E.03592
G1 X82.731 Y99.288 E.10506
G1 X83.002 Y99.55 F9000
G1 F1106
G1 X83.044 Y99.507 E.00188
G1 X84.428 Y98.643 E.05115
G1 X85.471 Y98.478 E.0331
G1 X129.194 Y98.478 E1.37092
G1 X130.778 Y98.872 E.05115
G1 X131.991 Y99.963 E.05115
G1 X132.571 Y101.855 E.06207
G1 X132.571 Y102.646 E.02479
G1 X132.177 Y104.229 E.05115
G1 X131.087 Y105.443 E.05115
G1 X129.387 Y106.018 E.05627
G1 X86.454 Y108.469 E1.34832
G1 X83.099 Y108.474 E.1052
G1 X81.516 Y108.08 E.05115
G1 X80.302 Y106.99 E.05115
G1 X79.722 Y105.097 E.06207
G1 X79.722 Y104.307 E.02479
G1 X80.116 Y102.723 E.05115
G1 X80.672 Y101.958 E.02966
G1 X82.961 Y99.593 E.10318
G1 E-4.2 F3600
;WIPE_START
G1 F7200
G1 X83.044 Y99.507 E-.057
G1 X84.428 Y98.643 E-.77494
G1 X85.471 Y98.478 E-.50141
G1 X86.264 Y98.478 E-.37664
;WIPE_END
G1 E-.09 F3600
G1 X85.718 Y102.103 F9000
G1 E6 F2400
;TYPE:External perimeter
G1 F1106
G1 X86.47 Y102.065 E.02359
G1 X128.684 Y102.065 E1.32358
G1 X128.904 Y102.095 E.00698
G1 X128.904 Y102.407 E.00977
G1 X128.681 Y102.436 E.00705
G1 X86.051 Y102.436 E1.33663
G1 X86.051 Y104.111 E.05252
G1 X86.012 Y104.848 E.02314
G1 X85.352 Y104.887 E.02074
G1 X83.566 Y104.887 E.05599
G1 X83.389 Y104.861 E.00561
G1 X83.389 Y104.544 E.00993
G1 X83.588 Y104.517 E.0063
G1 X85.681 Y104.517 E.06562
G1 X85.681 Y102.841 E.05253
G1 X85.715 Y102.163 E.02129
G1 X86.07 Y102.293 F9000
M106 S255
;LAYER_CHANGE
;Z:0.36
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;0.36


G1 E-4.2 F3600
;WIPE_START
G1 F7200
G1 X86.47 Y102.065 E-.36137
G1 X89.309 Y102.065 E-1.34863
;WIPE_END
G1 E-.09 F3600
G1 Z.36 F9000
;AFTER_LAYER_CHANGE
;0.36
M104 S205 ; set temperature
G1 X89.309 Y98.101
G1 E6 F2400
;TYPE:Skirt/Brim
G1 F1063
G1 X129.194 Y98.101 E1.02324
G1 X130.87 Y98.496 E.04416
G1 X132.193 Y99.597 E.04416
G1 X132.949 Y101.855 E.06109
G1 X132.949 Y102.646 E.02028
G1 X132.554 Y104.322 E.04416
G1 X131.453 Y105.645 E.04416
G1 X129.408 Y106.394 E.05586
G1 X86.475 Y108.845 E1.10321
G1 X83.099 Y108.851 E.08663
G1 X81.423 Y108.457 E.04416
G1 X80.1 Y107.356 E.04416
G1 X79.345 Y105.097 E.06109
G1 X79.345 Y104.307 E.02028
G1 X79.739 Y102.631 E.04416
G1 X80.401 Y101.696 E.02939
G1 X82.773 Y99.245 E.0875
G1 X84.222 Y98.315 E.04416
G1 X85.471 Y98.101 E.03251
G1 X89.249 Y98.101 E.09693
G1 X89.249 Y98.478 F9000
G1 F1063
G1 X129.194 Y98.478 E1.02478
G1 X130.778 Y98.872 E.04185
G1 X131.991 Y99.963 E.04185
G1 X132.571 Y101.855 E.05079
G1 X132.571 Y102.646 E.02028
G1 X132.177 Y104.229 E.04185
G1 X131.087 Y105.443 E.04185
G1 X129.387 Y106.018 E.04604
G1 X86.454 Y108.469 E1.10321
G1 X83.099 Y108.474 E.08607
G1 X81.516 Y108.08 E.04185
G1 X80.302 Y106.99 E.04185
G1 X79.722 Y105.097 E.05079
G1 X79.722 Y104.307 E.02028
G1 X80.116 Y102.723 E.04185
G1 X80.672 Y101.958 E.02427
G1 X83.044 Y99.507 E.0875
G1 X84.428 Y98.643 E.04185
G1 X85.471 Y98.478 E.02708
G1 X89.189 Y98.478 E.09539
G1 E-4.2 F3600
;WIPE_START
G1 F7200
G1 X92.789 Y98.478 E-1.71
;WIPE_END
G1 E-.09 F3600
G1 X86.036 Y102.421 F9000
G1 E6 F2400
;TYPE:External perimeter
;WIDTH:0.45
G1 F1063
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
;LAYER_CHANGE
;Z:0.52
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;0.52


G1 E-4.2 F3600
;WIPE_START
G1 F7200
G1 X86.036 Y104.872 E-1.1646
G1 X84.888 Y104.872 E-.5454
;WIPE_END
G1 E-.09 F3600
G1 Z.52 F9000
;AFTER_LAYER_CHANGE
;0.52
G1 X86.036 Y102.421
G1 E6 F2400
G1 F900
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
;LAYER_CHANGE
;Z:0.68
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;0.68


G1 E-4.2 F3600
;WIPE_START
G1 F7200
G1 X86.036 Y104.872 E-1.1646
G1 X84.888 Y104.872 E-.5454
;WIPE_END
G1 E-.09 F3600
G1 Z.68 F9000
;AFTER_LAYER_CHANGE
;0.68
G1 X86.036 Y102.421
G1 E6 F2400
G1 F900
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
;LAYER_CHANGE
;Z:0.84
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;0.84


G1 E-4.2 F3600
;WIPE_START
G1 F7200
G1 X86.036 Y104.872 E-1.1646
G1 X84.888 Y104.872 E-.5454
;WIPE_END
G1 E-.09 F3600
G1 Z.84 F9000
;AFTER_LAYER_CHANGE
;0.84
G1 X86.036 Y102.421
G1 E6 F2400
G1 F900
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
;LAYER_CHANGE
;Z:1
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;1


G1 E-4.2 F3600
;WIPE_START
G1 F7200
G1 X86.036 Y104.872 E-1.1646
G1 X84.888 Y104.872 E-.5454
;WIPE_END
G1 E-.09 F3600
G1 Z1 F9000
;AFTER_LAYER_CHANGE
;1
G1 X86.036 Y102.421
G1 E6 F2400
G1 F900
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
;LAYER_CHANGE
;Z:1.16
;HEIGHT:0.16
;BEFORE_LAYER_CHANGE
G92 E0
;1.16


G1 E-4.2 F3600
;WIPE_START
G1 F7200
G1 X86.036 Y104.872 E-1.1646
G1 X84.888 Y104.872 E-.5454
;WIPE_END
G1 E-.09 F3600
G1 Z1.16 F9000
;AFTER_LAYER_CHANGE
;1.16
G1 X86.036 Y102.421
G1 E6 F2400
G1 F900
G1 X86.036 Y104.872 E.06777
G1 X83.324 Y104.872 E.075
G1 X83.324 Y104.532 E.00942
G1 X85.696 Y104.532 E.06559
G1 X85.696 Y102.08 E.06777
G1 X128.969 Y102.08 E1.19652
G1 X128.969 Y102.421 E.00942
G1 X86.096 Y102.421 E1.18544
G1 X85.636 Y102.422 F9000
G1 E-4.2 F3600
;WIPE_START
G1 F7200;_WIPE
G1 X86.036 Y104.872 E-1.1646
G1 F7200;_WIPE
G1 X84.888 Y104.872 E-.5454
;WIPE_END
G1 E-.09 F3600
M107
;TYPE:Custom
; Filament-specific end gcode 
;END gcode for filament
G1 Z3.16 F600 ; Move print bed down
G1 X50 Y50 F9000 ; move print head out of the way
G1 Z390 F600 ; Move print bed close to the bottom
M140 S0 ; turn off heatbed
M104 S0 ; turn off temperature
M107 ; turn off fan
M84 X Y E ; disable motors
; filament used [mm] = 32.42
; filament used [cm3] = 0.08
; filament used [g] = 0.10
; filament cost = 0.00
; total filament used [g] = 0.10
; total filament cost = 0.00
; estimated printing time (normal mode) = 3m 12s

; prusaslicer_config = begin
; avoid_crossing_perimeters = 0
; avoid_crossing_perimeters_max_detour = 0
; bed_custom_model = 
; bed_custom_texture = 
; bed_shape = 5x5,355x5,355x355,5x355
; bed_temperature = 40
; before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0\n;{layer_z}\n\n
; between_objects_gcode = 
; bottom_fill_pattern = monotonic
; bottom_solid_layers = 5
; bottom_solid_min_thickness = 0
; bridge_acceleration = 250
; bridge_angle = 0
; bridge_fan_speed = 100
; bridge_flow_ratio = 0.85
; bridge_speed = 25
; brim_separation = 0
; brim_type = outer_only
; brim_width = 0
; clip_multipart_objects = 1
; color_change_gcode = M600
; compatible_printers_condition_cummulative = "printer_model=~/(ENDER|CR|SERMOON).*/ and nozzle_diameter[0]==0.4";printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
; complete_objects = 0
; cooling = 1
; cooling_tube_length = 5
; cooling_tube_retraction = 91.5
; default_acceleration = 500
; default_filament_profile = "Generic PLA @CREALITY"
; default_print_profile = 0.16mm OPTIMAL @CREALITY
; deretract_speed = 40
; disable_fan_first_layers = 1
; dont_support_bridges = 1
; draft_shield = disabled
; duplicate_distance = 6
; elefant_foot_compensation = 0.1
; end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
; end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600{endif} ; Move print bed down\nG1 X50 Y50 F{travel_speed*60} ; move print head out of the way\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+max_print_height-10} F600{endif} ; Move print bed close to the bottom\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
; ensure_vertical_shell_thickness = 1
; external_perimeter_extrusion_width = 0.45
; external_perimeter_speed = 25
; external_perimeters_first = 0
; extra_loading_move = -2
; extra_perimeters = 0
; extruder_clearance_height = 34
; extruder_clearance_radius = 47
; extruder_colour = #FCE94F
; extruder_offset = 0x0
; extrusion_axis = E
; extrusion_multiplier = 1
; extrusion_width = 0.45
; fan_always_on = 1
; fan_below_layer_time = 100
; filament_colour = #DDDDDD
; filament_cooling_final_speed = 3.4
; filament_cooling_initial_speed = 2.2
; filament_cooling_moves = 4
; filament_cost = 20
; filament_density = 1.24
; filament_diameter = 1.75
; filament_load_time = 0
; filament_loading_speed = 28
; filament_loading_speed_start = 3
; filament_max_volumetric_speed = 15
; filament_minimal_purge_on_wipe_tower = 15
; filament_notes = ""
; filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
; filament_settings_id = "Generic PLA @CREALITY"
; filament_soluble = 0
; filament_spool_weight = 0
; filament_toolchange_delay = 0
; filament_type = PLA
; filament_unload_time = 0
; filament_unloading_speed = 90
; filament_unloading_speed_start = 100
; filament_vendor = Generic
; fill_angle = 45
; fill_density = 15%
; fill_pattern = grid
; first_layer_acceleration = 0
; first_layer_acceleration_over_raft = 0
; first_layer_bed_temperature = 40
; first_layer_extrusion_width = 0.42
; first_layer_height = 0.2
; first_layer_speed = 20
; first_layer_speed_over_raft = 30
; first_layer_temperature = 210
; full_fan_speed_layer = 0
; fuzzy_skin = none
; fuzzy_skin_point_dist = 0.8
; fuzzy_skin_thickness = 0.3
; gap_fill_enabled = 1
; gap_fill_speed = 30
; gcode_comments = 0
; gcode_flavor = marlin
; gcode_label_objects = 0
; gcode_resolution = 0.0125
; gcode_substitutions = 
; high_current_on_filament_swap = 0
; host_type = octoprint
; infill_acceleration = 0
; infill_anchor = 600%
; infill_anchor_max = 50
; infill_every_layers = 1
; infill_extruder = 1
; infill_extrusion_width = 0.45
; infill_first = 0
; infill_only_where_needed = 0
; infill_overlap = 25%
; infill_speed = 50
; inherits_cummulative = "0.16mm OPTIMAL @CREALITY";"Generic PLA @CREALITY";
; interface_shells = 0
; ironing = 0
; ironing_flowrate = 15%
; ironing_spacing = 0.1
; ironing_speed = 15
; ironing_type = top
; layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
; layer_height = 0.16
; machine_limits_usage = time_estimate_only
; machine_max_acceleration_e = 1000
; machine_max_acceleration_extruding = 500
; machine_max_acceleration_retracting = 1000
; machine_max_acceleration_travel = 1500,1250
; machine_max_acceleration_x = 500
; machine_max_acceleration_y = 500
; machine_max_acceleration_z = 100
; machine_max_feedrate_e = 60
; machine_max_feedrate_x = 300
; machine_max_feedrate_y = 300
; machine_max_feedrate_z = 5
; machine_max_jerk_e = 5
; machine_max_jerk_x = 8
; machine_max_jerk_y = 8
; machine_max_jerk_z = 0.4
; machine_min_extruding_rate = 0
; machine_min_travel_rate = 0
; max_fan_speed = 100
; max_layer_height = 0.28
; max_print_height = 400
; max_print_speed = 100
; max_volumetric_speed = 0
; min_fan_speed = 100
; min_layer_height = 0.08
; min_print_speed = 15
; min_skirt_length = 4
; mmu_segmented_region_max_width = 0
; notes = 
; nozzle_diameter = 0.4
; only_retract_when_crossing_perimeters = 0
; ooze_prevention = 0
; output_filename_format = {input_filename_base}_{print_time}_{digits(layer_height,1,2)}mm_{temperature[0]}C_{filament_type[0]}_{printer_model}.gcode
; overhangs = 0
; parking_pos_retraction = 92
; pause_print_gcode = 
; perimeter_acceleration = 0
; perimeter_extruder = 1
; perimeter_extrusion_width = 0.45
; perimeter_speed = 40
; perimeters = 2
; physical_printer_settings_id = 
; post_process = 
; print_settings_id = 0.16mm OPTIMAL @CREALITY - Kopia
; printer_model = ENDER5PLUS
; printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_ENDER5PLUS\nPRINTER_HAS_BOWDEN
; printer_settings_id = Creality Ender-5 Plus
; printer_technology = FFF
; printer_variant = 0.4
; printer_vendor = 
; raft_contact_distance = 0.1
; raft_expansion = 1.5
; raft_first_layer_density = 90%
; raft_first_layer_expansion = 3
; raft_layers = 0
; remaining_times = 0
; resolution = 0
; retract_before_travel = 2
; retract_before_wipe = 70%
; retract_layer_change = 1
; retract_length = 6
; retract_length_toolchange = 1
; retract_lift = 0
; retract_lift_above = 0
; retract_lift_below = 0
; retract_restart_extra = 0
; retract_restart_extra_toolchange = 0
; retract_speed = 60
; seam_position = nearest
; silent_mode = 0
; single_extruder_multi_material = 0
; single_extruder_multi_material_priming = 0
; skirt_distance = 3
; skirt_height = 2
; skirts = 1
; slice_closing_radius = 0.049
; slicing_mode = regular
; slowdown_below_layer_time = 20
; small_perimeter_speed = 25
; solid_infill_below_area = 0
; solid_infill_every_layers = 0
; solid_infill_extruder = 1
; solid_infill_extrusion_width = 0.45
; solid_infill_speed = 40
; spiral_vase = 0
; standby_temperature_delta = -5
; start_filament_gcode = "; Filament gcode\n"
; start_gcode = G90 ; use absolute coordinates\nM83 ; extruder relative mode\nM140 S{first_layer_bed_temperature[0]} ; set final bed temp\nM104 S150 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM190 S{first_layer_bed_temperature[0]} ; wait for bed temp to stabilize\nG28 ; home all axis\nG29 ; auto bed levelling\nG1 Z50 F240\nG1 X2 Y10 F3000\nM104 S{first_layer_temperature[0]} ; set final nozzle temp\nM109 S{first_layer_temperature[0]} ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0
; support_material = 0
; support_material_angle = 0
; support_material_auto = 1
; support_material_bottom_contact_distance = 0
; support_material_bottom_interface_layers = -1
; support_material_buildplate_only = 0
; support_material_closing_radius = 2
; support_material_contact_distance = 0.15
; support_material_enforce_layers = 0
; support_material_extruder = 0
; support_material_extrusion_width = 0.38
; support_material_interface_contact_loops = 0
; support_material_interface_extruder = 0
; support_material_interface_layers = 2
; support_material_interface_pattern = rectilinear
; support_material_interface_spacing = 0.2
; support_material_interface_speed = 100%
; support_material_pattern = rectilinear
; support_material_spacing = 2
; support_material_speed = 40
; support_material_style = grid
; support_material_synchronize_layers = 0
; support_material_threshold = 40
; support_material_with_sheath = 0
; support_material_xy_spacing = 60%
; temperature = 205
; template_custom_gcode = 
; thick_bridges = 0
; thin_walls = 0
; threads = 4
; thumbnails = 
; toolchange_gcode = 
; top_fill_pattern = monotonic
; top_infill_extrusion_width = 0.4
; top_solid_infill_speed = 30
; top_solid_layers = 7
; top_solid_min_thickness = 0
; travel_speed = 150
; travel_speed_z = 0
; use_firmware_retraction = 0
; use_relative_e_distances = 1
; use_volumetric_e = 0
; variable_layer_height = 1
; wipe = 1
; wipe_into_infill = 0
; wipe_into_objects = 0
; wipe_tower = 0
; wipe_tower_bridging = 10
; wipe_tower_brim_width = 2
; wipe_tower_no_sparse_layers = 0
; wipe_tower_rotation_angle = 0
; wipe_tower_width = 60
; wipe_tower_x = 170
; wipe_tower_y = 140
; wiping_volumes_extruders = 70,70
; wiping_volumes_matrix = 0
; xy_size_compensation = 0
; z_offset = 0
; prusaslicer_config = end

[konradsdev1]

Prawdopodobnie różnica wynika z tego, że dla 5 jest dodane:

Kod: Zaznacz cały

G29 ; auto bed levelling

Spróbuj usunąć tą linijkę albo dodaj G90 zaraz po niej.

[TomekToJa]

Ok, dziękuję wszystkim. Nie przeciągam tematu.

Wykonałem kopiuj/wklej.

Skopiowałem kod z początku jak na profilu Ender 3 i wkleiłem go do profilu Ender 5 -działa jak chcę.

Zastanawia mnie za to odpalenie opcji automatycznego wyjęcia filamentu z hotendu na koniec druku. Tak aby nie było filamentu w hotendzie gdy drukarka nie pracuje i zarazem zabieg ułatwi zmianę filamentu na inny przed kolejnym wydrukiem.
Czy ktoś z was ma to uruchomiene?
W którym miejscu i jakim kodem oraz jak to się sprawdza?

[morf]

a to zmieniasz filament za kazdym wydrukiem?
bez sensu IMHO

[Grzesinski]

Ok, dziękuję wszystkim. Nie przeciągam tematu.

Zastanawia mnie za to odpalenie opcji automatycznego wyjęcia filamentu z hotendu na koniec druku. Tak aby nie było filamentu w hotendzie gdy drukarka nie pracuje i zarazem zabieg ułatwi zmianę filamentu na inny przed kolejnym wydrukiem.
Czy ktoś z was ma to uruchomiene?

Tak mam to uruchomione, od kilku dni. Jako uzupełnienie automatycznego wyłączania drukarki po zakończeniu pracy.
Chociaż wydruki można później zabrać od ręki za to to wyjęcie filamentu wymaga czasu na rozgrzewanie głowicy i to chciałem wyeliminować.
Na razie testuje czy tak wyjdzie wygodniej, zobaczymy.
Wiadomo, że przed kolejnym wydrukiem konieczne będzie załadowanie materiału więc użyteczność zależy od tego czy często zdejmuje się szpule czy nie (dla zmiany materiału czy schowania go do pudła). U mnie rotacja materiału jest spora a i sprzęt nie pracuje non-stop.

[TomekToJa]

Ok, dziękuję wszystkim. Nie przeciągam tematu.

Zastanawia mnie za to odpalenie opcji automatycznego wyjęcia filamentu z hotendu na koniec druku. Tak aby nie było filamentu w hotendzie gdy drukarka nie pracuje i zarazem zabieg ułatwi zmianę filamentu na inny przed kolejnym wydrukiem.
Czy ktoś z was ma to uruchomiene?

Tak mam to uruchomione, od kilku dni. Jako uzupełnienie automatycznego wyłączania drukarki po zakończeniu pracy.
Chociaż wydruki można później zabrać od ręki za to to wyjęcie filamentu wymaga czasu na rozgrzewanie głowicy i to chciałem wyeliminować.
Na razie testuje czy tak wyjdzie wygodniej, zobaczymy.
Wiadomo, że przed kolejnym wydrukiem konieczne będzie załadowanie materiału więc użyteczność zależy od tego czy często zdejmuje się szpule czy nie (dla zmiany materiału czy schowania go do pudła). U mnie rotacja materiału jest spora a i sprzęt nie pracuje non-stop.

A podaj gdzie i co wpisywałeś w gcode pliss

[Grzesinski]

W slicerze (u mnie Prusa) do końcowego Gcodu [Prusa: Ustawienia drukarki - Własny Gcode - Gcode końcowy]
dodajesz zaraz na początku (żeby hotend nie wystygł)
M702
https://marlinfw.org/docs/gcode/M702.html
Zachowanie (długość, temperatura minimalna itp) skonfigurowane są podczas kompilacji Marlina, ale możesz je nadpisać własnymi jeśli nie masz tego właściwie ustawionego.