- Wgraj raz jeszcze Marlina, zmieniając w configuration.h rozmiar stołu:
Kod: Zaznacz cały
#define X_BED_SIZE 235 #define Y_BED_SIZE 235
- W Cura przywróć Width i Depth: 235 mm
PS Sorry za post pod postem post pod postem post pod postem.
Kod: Zaznacz cały
#define X_BED_SIZE 235
#define Y_BED_SIZE 235
Zakładka Marlin:FlameRunner pisze:Ty masz wgranego Marlina? Pewnie z tym configiem: https://github.com/MarlinFirmware/Marli ... ion.h#L878 ?
Kod: Zaznacz cały
#define BAUDRATE 115200
// Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH
// The following define selects which electronics board you have.
// Please choose the name from boards.h that matches your setup
#ifndef MOTHERBOARD
#define MOTHERBOARD BOARD_MKS_GEN_L
#endif
// Optional custom name for your RepStrap or other custom machine
// Displayed in the LCD "Ready" message
#define CUSTOM_MACHINE_NAME "Ender 3"
// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
// @section extruder
// This defines the number of extruders
// :[1, 2, 3, 4, 5]
#define EXTRUDERS 1
// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
// For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE
Kod: Zaznacz cały
// @section extruder
// For direct drive extruder v9 set to true, for geared extruder set to false.
#define INVERT_E0_DIR false
#define INVERT_E1_DIR false
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
// @section homing
//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case.
// Direction of endstops when homing; 1=MAX, -1=MIN
// :[-1,1]
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Z_HOME_DIR -1
// @section machine
// The size of the print bed
#define X_BED_SIZE 220
#define Y_BED_SIZE 220
// Travel limits (mm) after homing, corresponding to endstop positions.
#define X_MIN_POS 0
#define Y_MIN_POS 0
#define Z_MIN_POS 0
#define X_MAX_POS X_BED_SIZE
#define Y_MAX_POS Y_BED_SIZE
#define Z_MAX_POS 250
/**
* Software Endstops
*
* - Prevent moves outside the set machine bounds.
* - Individual axes can be disabled, if desired.
* - X and Y only apply to Cartesian robots.
* - Use 'M211' to set software endstops on/off or report current state
*/
// Min software endstops constrain movement within minimum coordinate bounds
#define MIN_SOFTWARE_ENDSTOPS
#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
#define MIN_SOFTWARE_ENDSTOP_X
#define MIN_SOFTWARE_ENDSTOP_Y
#define MIN_SOFTWARE_ENDSTOP_Z
#endif
// Max software endstops constrain movement within maximum coordinate bounds
#define MAX_SOFTWARE_ENDSTOPS
#if ENABLED(MAX_SOFTWARE_ENDSTOPS)
#define MAX_SOFTWARE_ENDSTOP_X
#define MAX_SOFTWARE_ENDSTOP_Y
#define MAX_SOFTWARE_ENDSTOP_Z
#endif
#if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS)
//#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
#endif
I bardzo dobrze, bo to jest oficjalna strona projektu Marlin, a pod "Latest release" masz bezpieczny wariant: najnowszą wersję, która jest gruntownie przetestowana i uznana za stabilną. W momencie, gdy dana drukarka (tak jak Ender-3) jest "dodana" do Marlin, pobieranie firmware z innych źródeł nie ma sensu dla typowego użytkownika.Abys pisze:ostatni chyba stąd: http://marlinfw.org/meta/download/
Kod: Zaznacz cały
// The size of the print bed
#define X_BED_SIZE 220
#define Y_BED_SIZE 220
Kod: Zaznacz cały
#define MOTHERBOARD BOARD_MKS_GEN_L
Czytałem,widziałem taki sposób na filmach yt.Domell pisze:czas zastygania materiału, opcja 1. Poprawić zwiększyć chłodzenie wydruku opcja 2 podczas drukowania adalindy jak naj dalej od niej daj coś jeszcze żeby materiał miał czas na zastygnięcie.
A jak zrobisz obie opcje to powinno być super.
Co powiecie na ten wydruk?FlameRunner pisze:Czy te prążki są podobne do śruby?
Czy występują w innych miejscach / na innych wydrukach niż kadłub statku?
Jeszcze kilka dni temu wydruki (niekompletna Adalinda) wyglądały na całkowicie wolne od tego problemu...?