Powiecie mi na przyszłość co w takiej sytuacji zrobić, bo !@#! byłem na końcu druku już gdy to się stało
Czy dało się to uratować jakimś sposobem tylko ja nie umiałem tego zrobić?
No i najważniejsze - teoretycznie przecież po tych logach dałoby się wznowić druk od tego samego miejsca?
Dodatkowo, mam ten nowy pronterface który zainstalował się razem z PrusaSlicer, wcześniej nie miałe tego silent/normal mode wie ktos co to jest?
Kod: Zaznacz cały
...
SILENT MODE: Percent done: 73; print time remaining in mins: 39
NORMAL MODE: Percent done: 73; print time remaining in mins: 38
SILENT MODE: Percent done: 73; print time remaining in mins: 39
NORMAL MODE: Percent done: 73; print time remaining in mins: 38
SILENT MODE: Percent done: 74; print time remaining in mins: 38
NORMAL MODE: Percent done: 74; print time remaining in mins: 37
SILENT MODE: Percent done: 74; print time remaining in mins: 38
NORMAL MODE: Percent done: 74; print time remaining in mins: 37
SILENT MODE: Percent done: 74; print time remaining in mins: 37
NORMAL MODE: Percent done: 75; print time remaining in mins: 36
SILENT MODE: Percent done: 74; print time remaining in mins: 37
NORMAL MODE: Percent done: 75; print time remaining in mins: 36
SILENT MODE: Percent done: 75; print time remaining in mins: 36
NORMAL MODE: Percent done: 76; print time remaining in mins: 35
SILENT MODE: Percent done: 75; print time remaining in mins: 36
NORMAL MODE: Percent done: 76; print time remaining in mins: 35
SILENT MODE: Percent done: 76; print time remaining in mins: 35
Print paused at: 13:23:34
Command not found!
start
echo: 3.7.0-2201
echo: Last Updated: Apr 1 2019 20:56:14 | Author: (none, default config)
Compiled: Apr 1 2019
echo: Free Memory: 2037 PlannerBufferBytes: 1392
echo:Hardcoded Default Settings Loaded
adc_init
CrashDetect ENABLED!
PAT9125_RES_X=0
PAT9125_RES_Y=240
PAT9125_init:1
PAT9125_RES_X=0
PAT9125_RES_Y=240
PAT9125_init:1
FSensor ENABLED
echo:SD card ok
fsensor_autoload_check_start - autoload ENABLED
Resuming.
Print resumed at: 13:27:02
fsensor_autoload_check_stop - autoload DISABLED
Error:Line Number is not Last Line Number+1, Last Line: 0
[ERROR] Error:Line Number is not Last Line Number+1, Last Line: 0
Resend: 1
[ERROR] Print thread died due to the following error:
Traceback (most recent call last):
File "printrun\printcore.pyc", line 471, in _print
File "printrun\printcore.pyc", line 509, in _sendnext
KeyError: 1
echo:endstops hit: Y:106.29
echo:enqueing "M83"
echo:enqueing "G1 E-1.000 F2700.000"
echo:enqueing "G1 Z 10.302 F 800.000"
echo:enqueing "CRASH_DETECTEDY"
tmc2130_home_enter(axes_mask=0x01)
echo:busy: processing
echo:busy: processing
0 step=46 mscnt= 738
tmc2130_home_exit tmc2130_sg_homing_axes_mask=0x01
tmc2130_home_enter(axes_mask=0x02)
echo:busy: processing
echo:busy: processing
echo:busy: processing
0 step= 1 mscnt= 29
tmc2130_home_exit tmc2130_sg_homing_axes_mask=0x02
echo:enqueing "CRASH_RECOVER"
echo:busy: processing
MMU not responding - DISABLED
echo: cold extrusion prevented
Resend: 1
fsensor_autoload_check_start - autoload ENABLED
Setting hotend temperature to 210.000000 degrees Celsius.
Setting bed temperature to 55.000000 degrees Celsius.
Print paused at: 13:28:47
Resuming.
Print resumed at: 13:28:49
[ERROR] Print thread died due to the following error:
Traceback (most recent call last):
File "printrun\printcore.pyc", line 471, in _print
File "printrun\printcore.pyc", line 509, in _sendnext
KeyError: 1
fsensor_autoload_check_stop - autoload DISABLED
fsensor_autoload_check_start - autoload ENABLED
Disconnected.