Corexy

Jakość druku Cię nie zadowala?
Krzysztof37
Konto z ograniczeniami
Postów w temacie: 61
Posty: 60
Rejestracja: 01 sie 2019, 22:15
x 4

Re: Corexy

Post autor: Krzysztof37 »

Jestem w pracy, jak wrócę dam parę zdjęć i dokładny opis
Krzysztof37
Konto z ograniczeniami
Postów w temacie: 61
Posty: 60
Rejestracja: 01 sie 2019, 22:15
x 4

Re: Corexy

Post autor: Krzysztof37 »

Ok, wiec tak, powtórzę się z danymi drukarki:
Drukarka to Two Tree Sapphire S coreXY
Modyfikacje:
Duet WiFi
BlTouch
Prowadnice Hiwin
Hotbed Keenovo 400W
Hotend Mosquito Slice Engineering
Nadmuch według tego projektu https://www.youtube.com/watch?v=fpymiHUSxEs
Do druku użyłem PLA Pro poniżej krotki opis:
PLA Pro combines two desirable features: simple printing as with normal PLA material but with properties that are comparable to those of ABS. The Spectrum PLA Pro has nearly 50% higher impact resistance after printing than ABS material.
i na koniec zdjecie ze slicera.
Co do odbicia lustrzanego to mam coś skopane w ustawieniach, ale nie wiem co :problem:
Załączniki
Przechwytywanie.PNG
Krzysztof37
Konto z ograniczeniami
Postów w temacie: 61
Posty: 60
Rejestracja: 01 sie 2019, 22:15
x 4

Re: Corexy

Post autor: Krzysztof37 »

Podam jeszcze mój aktualny config.g

Kod: Zaznacz cały

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Sat Aug 03 2019 03:22:52 GMT+0100 (Brytyjski czas letni)

; General preferences
G90                                      ; Send absolute coordinates...
M83                                      ; ...but relative extruder moves

M667 S1                                  ; Select CoreXY mode

; Network
M550 P"My Printer"                       ; Set machine name
M552 S1                                  ; Enable network
M587 S"ASUS" --------               ; Configure access point. You can delete this line once connected
M586 P0 S1                               ; Enable HTTP
M586 P1 S0                               ; Disable FTP
M586 P2 S0                               ; Disable Telnet

; Drives
M569 P0 S0                               ; Physical drive 0 goes backwards
M569 P1 S0                               ; Physical drive 1 goes backwards
M569 P2 S1                               ; Physical drive 2 goes forwards
M569 P3 S0                               ; Physical drive 3 goes backwards
M92 X80.00 Y80.00 Z1600 E416             ; Set steps per mm
M350 X16 Y16 Z16 E16 I1                  ; Configure microstepping with interpolation
M566 X900.00 Y900.00 Z12.00 E120.00      ; Set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00  ; Set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00      ; Set accelerations (mm/s^2)
M906 X900.00 Y900.00 Z1100.00 E900.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                  ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                         ; Set axis minima
M208 X200 Y200 Z200 S1.6                 ; Set axis maxima

; Endstops
M574 X2 Y2 S0                            ; X home to min. Y and Z home to max. Normally Closed limit switches. 
M574 Z1 S2                               ; Define Z to use Probe. Home to Min
M557 X5:205 Y5:200 S20                   ; Define mesh grid
M558 P5 H5 F500 T4000                    ; Set Z probe type/mode 5. H=Dive Height. F=Speed the bed moves
G31 P25 X0 Y-35.40 Z1.20                 ; Z probe trigger value, offset in relation to nozzle. And trigger height adjustment

; Heaters
M305 P0 T100000 B4138 R4700              ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                             ; Set temperature limit for heater 0 to 120C
M305 P1 T613400 B5025 C1.484206e-7 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280                             ; Set temperature limit for heater 1 to 280C

; BLTouch - Heaters
M307 H7 A-1 C-1 D-1                      ; Disable the 7th Heater to free up PWM channel 5 on the Duet WiFi board.

; Fans
M106 P0 S0 I0 F500 H T45                 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45                ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                            ; Define tool 0

M501

; Automatic saving after power loss is not enabled

; Custom settings are not configured
Krzysztof37
Konto z ograniczeniami
Postów w temacie: 61
Posty: 60
Rejestracja: 01 sie 2019, 22:15
x 4

Re: Corexy

Post autor: Krzysztof37 »

A to jest config od gościa z Thingiwerse z tej samej drukarki na duecie i na tych ustawieniach hołmuje mu w lewym tylnym rogu, skopiowałem cześć "Drivers: z jego configu do mnie , ale wtedy moja drukarka hołmuje po przeciwnej stronie tam gdzie nie ma end stopu, zamieniłem podłączenie silników xy, tez nic, potem dodałem do configu w poleceniu M667 S-1 czyli dodałem minus, tez nic

Kod: Zaznacz cały

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes backwards
M350 Z16 E16 I0 ; Configure microstepping without interpolation
M350 X16 Y16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E400.00 ; Set steps per mm
M566 X900.00 Y900.00 Z12.00 E265.98 ; Set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z1050.00 E5100.00 ; Set maximum speeds (mm/min)
M201 X1800.00 Y1800.00 Z100.00 E5000.00 ; Set accelerations (mm/s^2)
M906 X900.00 Y900.00 Z1100.00 E900.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X200 Y188 Z248 S0 ; Set axis maxima

; Endstops
M574 X1 Y2 Z1 S0 ; Set active low and disabled endstops

; Z-Probe
M558 P0 H0 F120 T6000 ; Disable Z probe but set dive height, probe speed and travel speed
M557 X15:5 Y15:195 S20 ; Define mesh grid

; Heaters
M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4138 R2200 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R2200 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0-1.0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1.0 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0.7 I0 F500 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
Krzysztof37
Konto z ograniczeniami
Postów w temacie: 61
Posty: 60
Rejestracja: 01 sie 2019, 22:15
x 4

Re: Corexy

Post autor: Krzysztof37 »

Wiec tak, spróbowałem ustawić mój config jeszcze raz i wydaje mi się ze dobrze to zrobiłem, ale problem plaga na tym, ze os X po uruchomieniu komendy home X, porusza się w przeciwna stronę czyli X+ a powinna X-. Z panelu głównego Dueta wszystkie kierunki działają dobrze, próbowałem zamienić wtyczki silników na płycie ale to zmienia tylko cala kinematykę. Czy ktoś możne pomoc mi rozwiązać ten problem?
Załączniki
reference.png
Krzysztof37
Konto z ograniczeniami
Postów w temacie: 61
Posty: 60
Rejestracja: 01 sie 2019, 22:15
x 4

Re: Corexy

Post autor: Krzysztof37 »

.
Krzysztof37
Konto z ograniczeniami
Postów w temacie: 61
Posty: 60
Rejestracja: 01 sie 2019, 22:15
x 4

Re: Corexy

Post autor: Krzysztof37 »

ok, problem rozwiązany, wystarczyło zmienień tylko wszystkie wartości na minus dla osi X w homeall, homex i homez
cardjunk
ODPOWIEDZ

Wróć do „Kalibracja, problemy”