Duet2Wifi Ekstruder szaleje

[damianqx]

Cześć, wiecie może co może być przyczyną tego że ekstruder wykonuje jakieś nerwowe ruchy, wali dużo filamentu i mieli w miejscu?
Jest to pierwsze podłączenie duet2wifi, kroki ekstrudera skalibrowane podaje tyle ile trzeba.
Film pokazujący problem: https://www.youtube.com/watch?v=ZvQPNjY ... e=youtu.be

[morf]

Wklej swój config.
Czy na pewno dobrze masz skonfigurowany slicer? Na reprap firmware a nie np repetier?

[damianqx]

A to dla reprapfirmware się inaczej slicer konfiguruje ? Jak to zrobić
// Dobra mam, siedziałem 2 godziny i szukałem problemu w ustawieniach a nie wpadłem na to że inny gcode musi być dla reprap....

Kod: Zaznacz cały

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Apr 05 2020 12:11:06 GMT+0200 (czas środkowoeuropejski letni)

; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"Sapphire Pro"                           ; set printer name

M667 S1                                        ; select CoreXY mode

; Network
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S0                                     ; physical drive 0 goes backwards
M569 P1 S0                                     ; physical drive 1 goes backwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S0                                     ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z1600.00 E440.00             ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00            ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00        ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00            ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30                   ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X220 Y220 Z210 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"!xstop"                           ; configure active-high endstop for low end on X via pin !xstop
M574 Y2 S1 P"!ystop"                           ; configure active-high endstop for high end on Y via pin !ystop
M574 Z1 S1 P"!zstop"                           ; configure active-high endstop for low end on Z via pin !zstop

; Z-Probe
M558 P0 H5 F120 T6000                          ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                       ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00                               ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280                                   ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit

M307 H0 A139.2 C514.4 D1.1 S1.00 V23.8 B0
M307 H1 A989.2 C241.8 D7.4 S1.00 V24.0 B0

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined