Witam wszystkich, tak się zastanawiam czy da radę zapisac na stałe do pamięci wyniki pomiaru stołu, bo wydrukowałem do delty taką sondę http://www.thingiverse.com/thing:315698/#comments lecz nie do końca jest to wygodne żeby przed każdym wydrukiem mierzyć stół, stąd moje pytanie. Jeśli temat w nieodpowiednim miejscu to przepraszam, nie wiedziałem gdzie go napisać
Pozdrawiam
Zapisywanie pomiaru Z probe do eeprom
- dragonn
- Zasłużony
- Postów w temacie: 3
- Posty: 6384
- Rejestracja: 12 gru 2016, 21:50
- Lokalizacja: Opole
- Drukarka: LUME
- x 1455
Re: Zapisywanie pomiaru Z probe do eeprom
Dobrze by było chyba podać jaki firmware . Ale ogólnie zainteresuj się komendami M500 i M501
- dragonn
- Zasłużony
- Postów w temacie: 3
- Posty: 6384
- Rejestracja: 12 gru 2016, 21:50
- Lokalizacja: Opole
- Drukarka: LUME
- x 1455
Re: Zapisywanie pomiaru Z probe do eeprom
EEPROM w Marlinie sobie włączyłeś? Domyślnie nie jest, po tym M500 powinno zapisać wszystko do EEPROM również próbę Z.
- Wioletowy
- Konto z ograniczeniami
- Postów w temacie: 4
- Posty: 225
- Rejestracja: 21 kwie 2017, 11:19
- Lokalizacja: Łódź
- Drukarka: A8, I3 Haribo
- x 3
Re: Zapisywanie pomiaru Z probe do eeprom
// EEPROM
//
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores parameters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//define this to enable EEPROM support
#define EEPROM_SETTINGS
#if ENABLED(EEPROM_SETTINGS)
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
#define EEPROM_CHITCHAT // Please keep turned on if you can.
#endif
tak wygląda linijka z EEPROM-włączyłem ale wolę się upewnić
//
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
// M500 - stores parameters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//define this to enable EEPROM support
#define EEPROM_SETTINGS
#if ENABLED(EEPROM_SETTINGS)
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
#define EEPROM_CHITCHAT // Please keep turned on if you can.
#endif
tak wygląda linijka z EEPROM-włączyłem ale wolę się upewnić
- dragonn
- Zasłużony
- Postów w temacie: 3
- Posty: 6384
- Rejestracja: 12 gru 2016, 21:50
- Lokalizacja: Opole
- Drukarka: LUME
- x 1455
Re: Zapisywanie pomiaru Z probe do eeprom
No jest dobrze . Czyli po próbie Z dodaj sobie M500 i powinno być git.
Wioletowy