migracja na duet3d pogorszenie jakosci

Czyli co i jak podłączyć żeby działało
Awatar użytkownika
morf
Drukarz
Postów w temacie: 20
Posty: 3202
Rejestracja: 17 sty 2017, 12:28
Drukarka: Reprapy, Prusa MK3S
x 1574

migracja na duet3d pogorszenie jakosci

Post autor: morf »

Czesc,
udalo mi sie znalesc pare chwil i przepialem moje corexy z repetiera due3doom na TMC2208/lv8729(na Z i E) na Duet3d wifi.

Mam jakas straszna padake jesli chodzi o jakosc zwyklej kostki, w ogole nie poznaje swojej drukarki :wtf:
Probowalem juz zmieniac acc/predkosc/mikrokrok w Ztce ale nie pomaga :cry: Temperatury tez obnizac/podwyzszac i przemierzylem kroki extrudera ale jest ok

Koledzy, pomozecie? :D

ponizej config.g

Kod: Zaznacz cały

; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Tue Jun 05 2018 23:04:14 GMT+0200 (CEST)

; General preferences
G90                                              ; Send absolute coordinates...
M83                                              ; ...but relative extruder moves

M667 S1                                          ; Select CoreXY mode

; Network
M550 PMorfPrinter                                ; Set machine name
M552 S1                                          ; Enable network
M587 S"ssid" P"haslo"; Configure access point. You can delete this line once connected
M586 P0 S1                                       ; Enable HTTP
M586 P1 S1                                       ; Enable FTP
M586 P2 S0                                       ; Disable Telnet

; Drives
M569 P0 S1                                       ; Drive 0 goes forwards
M569 P1 S1                                       ; Drive 1 goes forwards
M569 P2 S0                                       ; Drive 2 goes forwards
M569 P3 S0                                       ; Drive 3 goes forwards
M350 X128 Y128 Z256 E128 I0                      ; Configure microstepping without interpolation
M92 X1280 Y1280 Z2560 E720                       ; Set steps per mm
M566 X1200 Y1200 Z12 E120                          ; Set maximum instantaneous speed changes (mm/min)
M203 X9000 Y9000 Z360 E3000                     ; Set maximum speeds (mm/min)
M201 X1500 Y1500 Z100 E5000                       ; Set accelerations (mm/s^2)
M906 X500 Y500 Z800 E600 I100                   ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                          ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                 ; Set axis minima
M208 X215 Y184 Z208.3 S0                           ; Set axis maxima

; Endstops
M574 X2 Y2 S0                                    ; Set active low endstops
M574 Z2 S1                                       ; Set active high endstops

; Z-Probe
;M558 P0 H5 F120 T6000                            ; Set Z probe type to switch and the dive height + speeds
;G31 P600 X0 Y0 Z2.5                              ; Set Z probe trigger value, offset and trigger height
;M557 X15:200 Y15:169 S20                         ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 C0 R4700                   ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                                     ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700         ; Set thermistor + ADC parameters for heater 1
M143 H1 S280                                     ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1                           ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                        ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45                        ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                                    ; Define tool 0
G10 P0 X0 Y0 Z0                                  ; Set tool 0 axis offsets
G10 P0 R0 S0                                     ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured
oraz screen z epromu repetierowego
Screenshot_20180712_185204.png
Screenshot_20180712_185301.png
no i padaczana kostka (powierzchnia zewnetrzna jest prosta ale optycznie jakies takie pasy jakby cos nie tak w Ztce sie dzialo
Screenshot_20180712_185513.png
dla przypomnienia wczesniej bylo tak:
Screenshot_20180712_185536.png
Done is better than perfect.
Awatar użytkownika
dragonn
Zasłużony
Postów w temacie: 10
Posty: 6383
Rejestracja: 12 gru 2016, 21:50
Lokalizacja: Opole
Drukarka: LUME
x 1455

Re: migracja na duet3d pogorszenie jakosci

Post autor: dragonn »

a spróbuj zwiększyć jerk na ekstuderze, normalnie Duet ma zdecydowanie za niski.
Awatar użytkownika
morf
Drukarz
Postów w temacie: 20
Posty: 3202
Rejestracja: 17 sty 2017, 12:28
Drukarka: Reprapy, Prusa MK3S
x 1574

Re: migracja na duet3d pogorszenie jakosci

Post autor: morf »

Kod: Zaznacz cały

M566 X1200 Y1200 Z12 E120                          ; Set maximum instantaneous speed changes (mm/min)
na ile? w Repetierze mialem chyba 15-20mm/s, 1200mm/min ustawic
Done is better than perfect.
Awatar użytkownika
dragonn
Zasłużony
Postów w temacie: 10
Posty: 6383
Rejestracja: 12 gru 2016, 21:50
Lokalizacja: Opole
Drukarka: LUME
x 1455

Re: migracja na duet3d pogorszenie jakosci

Post autor: dragonn »

No ustaw tyle.
jarn
Postów w temacie: 3
Posty: 200
Rejestracja: 06 maja 2017, 00:13
Lokalizacja: Strzelno
Drukarka: Delta, HevORT
x 37

Re: migracja na duet3d pogorszenie jakosci

Post autor: jarn »

Zmień filament.

Ja mam tak:
M566 X1200 Y1200 Z1200 E1200 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z18000 E9000 ; Set maximum speeds (mm/min)
M201 X2700 Y2700 Z2700 E4000 ; Set accelerations (mm/s^2)
M906 X2000 Y2000 Z2000 E1700 I40 ; Set motor currents (mA) and motor idle factor in per cent

ale na delcie.
Awatar użytkownika
morf
Drukarz
Postów w temacie: 20
Posty: 3202
Rejestracja: 17 sty 2017, 12:28
Drukarka: Reprapy, Prusa MK3S
x 1574

Re: migracja na duet3d pogorszenie jakosci

Post autor: morf »

zmienilem ale przelomu nie ma :(
Done is better than perfect.
Awatar użytkownika
dragonn
Zasłużony
Postów w temacie: 10
Posty: 6383
Rejestracja: 12 gru 2016, 21:50
Lokalizacja: Opole
Drukarka: LUME
x 1455

Re: migracja na duet3d pogorszenie jakosci

Post autor: dragonn »

pokombinuj jeszcze z temperaturą - od razu mówię, 210 C na Duet nie musi być równe 210 C na RAMPS+Marlin. Spróbuj dać 10C mniej.
Awatar użytkownika
morf
Drukarz
Postów w temacie: 20
Posty: 3202
Rejestracja: 17 sty 2017, 12:28
Drukarka: Reprapy, Prusa MK3S
x 1574

Re: migracja na duet3d pogorszenie jakosci

Post autor: morf »

Uff przerzucilem sie na petg rubinowy ale jest rownie masakra albo nawet bardziej,
najgorzej na naroznikach i zakretach wszystko sie jakby podwija probowalem zjechac z temperatura do 190C co dla petg wydaje mi sie mega podejrzane.
Jakgdyby jakis overextrusion?
Drukuje wieze ale wyniki nie przypominaja nawet moich wydrukow sprzed 3 lat :)
Zmiana extrusion po bandzie np na 90% tez nie daje zbytnio rezultatu jaki bym oczekiwal :(
20180713_221013.jpg
20180713_225048.jpg
Done is better than perfect.
Awatar użytkownika
dragonn
Zasłużony
Postów w temacie: 10
Posty: 6383
Rejestracja: 12 gru 2016, 21:50
Lokalizacja: Opole
Drukarka: LUME
x 1455

Re: migracja na duet3d pogorszenie jakosci

Post autor: dragonn »

190 dla PET-G to jest grubo coś nie tak, sprawdź ustawienia termistora.

Wysłane z mojego K10000 przy użyciu Tapatalka
Awatar użytkownika
morf
Drukarz
Postów w temacie: 20
Posty: 3202
Rejestracja: 17 sty 2017, 12:28
Drukarka: Reprapy, Prusa MK3S
x 1574

Re: migracja na duet3d pogorszenie jakosci

Post autor: morf »

Kod: Zaznacz cały

M305 P1 T100000 B4725 C7.060000e-8 R4700         ; Set thermistor + ADC parameters for heater 1
wg info dla termistora od e3d v6 orginal

na 190C ledwo szlo wiec jednak cos chyba tam dziala ten termistor :no:
Done is better than perfect.
ODPOWIEDZ

Wróć do „Elektronika sterująca, wyświetlacze”