Sbase V1.3 + TFT32 - pomocy przy uruchamianiu.
- MarioM06
- Konto z ograniczeniami
- Postów w temacie: 10
- Posty: 113
- Rejestracja: 05 maja 2018, 11:44
- Lokalizacja: Goczałkowice-Zdrój
- x 29
Re: Sbase V1.3 + TFT32 - pomocy przy uruchamianiu.
Na dzień dzisiejszy nadal wszystko na biurku ale mam już kontrolę nad podłączonym silnikiem osi Z przez TFT. Odczyt temp. hotendu też jest. Wygląda na to że powinno to zadziałać.
Więc teraz pewnie zacznę powoli zbierać części na nową drukarkę, bo szczerze to nie chcę robić demolki w tych co mam bo są dość dobrze dograne.
Dziękuję za wszystkie odpowiedzi były bardzo pomocne w większości. Jak prace nad drukarką ruszą to jest szansa, że będę miał jeszcze jakieś pytania.
Więc teraz pewnie zacznę powoli zbierać części na nową drukarkę, bo szczerze to nie chcę robić demolki w tych co mam bo są dość dobrze dograne.
Dziękuję za wszystkie odpowiedzi były bardzo pomocne w większości. Jak prace nad drukarką ruszą to jest szansa, że będę miał jeszcze jakieś pytania.
UltiAnet 240x240x290,
Wielka Siostra 430x430x400
Wielka Siostra 430x430x400
Re: Sbase V1.3 + TFT32 - pomocy przy uruchamianiu.
Wprowadzasz człowieka w błąd i nie czytasz ze zrozumieniem.
Kolega założył topik "Sbase V1.3 + TFT32 "
A ty mu proponujesz konfigurację:
#mainboard firmware setting(marlin:1; repetier:2; smoothie:3)
>cfg_firmware_type:1
Jak już się poddacie to dam całą konfigurację działającą dla płyty i tft
rafaljot kolego ja nie muszę nic układać to wy się motacie i wprowadzacie ludzi w błąd udając speców.
Dlatego jest 300 wpisów i brak rezultatów. Powyżej Wasze mądrości.
Dla tej części kodu prawidłowo:
#mainboard firmware setting(marlin:1; repetier:2; smoothie:3)
>cfg_firmware_type:3
Kolega założył topik "Sbase V1.3 + TFT32 "
A ty mu proponujesz konfigurację:
#mainboard firmware setting(marlin:1; repetier:2; smoothie:3)
>cfg_firmware_type:1
Jak już się poddacie to dam całą konfigurację działającą dla płyty i tft
rafaljot kolego ja nie muszę nic układać to wy się motacie i wprowadzacie ludzi w błąd udając speców.
Dlatego jest 300 wpisów i brak rezultatów. Powyżej Wasze mądrości.
Dla tej części kodu prawidłowo:
#mainboard firmware setting(marlin:1; repetier:2; smoothie:3)
>cfg_firmware_type:3
Re: Sbase V1.3 + TFT32 - pomocy przy uruchamianiu.
MarioM06 napisz na Prv to Ci podrzucę config.
Problemem jest przeliczenie stepów dla Smoteiego
Problemem jest przeliczenie stepów dla Smoteiego
- MarioM06
- Konto z ograniczeniami
- Postów w temacie: 10
- Posty: 113
- Rejestracja: 05 maja 2018, 11:44
- Lokalizacja: Goczałkowice-Zdrój
- x 29
Re: Sbase V1.3 + TFT32 - pomocy przy uruchamianiu.
Panowie prosiłbym po pierwsze o niedogryzanie sobie wzajemnie bo po prostu czytać tego się odechciewa. Niestety to już takie standardy ogólno-forumowe.
Za posty które mi pomogły "piwo postawiłem", bo takie głupoty jak konieczność obrócenia wtyczek o 180* bardzo utrudniają pracę zielonemu w temacie. Nikt nie zwrócił mi uwagi na fakt że, po znaczku # wszystko jest traktowane jako komentarz co niestety też nie jest oczywiste dla zielonego. Niby jest to napisane w configu ale angielski techniczny nie zawsze jest zrozumiały w 100% i trzeba się domyślać.
Przed założeniem tematu czytałem różna pomocne strony, nie jest tak że, bez żadnej wiedzy chcę żebyście to za mnie zrobili. Ale diabeł tkwi w szczegółach które pomagacie zauważyć, za co dziękuję.
Aktualny config który mam na karcie:
Dalszej konfiguracji robić nie będę dopóki nie będę miał jakiejś kompletniejszej drukarki do tego podłączonej. Na tym config działają już oba wyświetlacze LCD i TFT, pokazują temp. i da się kręcić podłączonym silnikiem. Pewnie jeszcze kilka rzeczy wyjdzie zanim całkiem to uruchomię ale to potem.
Ewentualne pytanie które teraz mi podsunąłeś czy TFT będzie działał z marlinem?
Za posty które mi pomogły "piwo postawiłem", bo takie głupoty jak konieczność obrócenia wtyczek o 180* bardzo utrudniają pracę zielonemu w temacie. Nikt nie zwrócił mi uwagi na fakt że, po znaczku # wszystko jest traktowane jako komentarz co niestety też nie jest oczywiste dla zielonego. Niby jest to napisane w configu ale angielski techniczny nie zawsze jest zrozumiały w 100% i trzeba się domyślać.
Przed założeniem tematu czytałem różna pomocne strony, nie jest tak że, bez żadnej wiedzy chcę żebyście to za mnie zrobili. Ale diabeł tkwi w szczegółach które pomagacie zauważyć, za co dziękuję.
Aktualny config który mam na karcie:
Kod: Zaznacz cały
# Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
# NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
## Robot module configurations : general handling of movement G-codes and slicing into moves
# Basic motion configuration
default_feed_rate 4000 # Default speed (mm/minute) for G1/G2/G3 moves
default_seek_rate 4000 # Default speed (mm/minute) for G0 moves
mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs, 0 to disable
#mm_per_line_segment 5 # Cut lines into segments this size
mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
# note it is invalid for both the above be 0
# if both are used, will use largest segment length based on radius
# Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
# See http://smoothieware.org/stepper-motors
alpha_steps_per_mm 80 # Steps per mm for alpha ( X ) stepper
beta_steps_per_mm 80 # Steps per mm for beta ( Y ) stepper
gamma_steps_per_mm 1600 # Steps per mm for gamma ( Z ) stepper
# Planner module configuration : Look-ahead and acceleration configuration
# See http://smoothieware.org/motion-control
acceleration 3000 # Acceleration in mm/second/second.
#z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
junction_deviation 0.05 # See http://smoothieware.org/motion-control#junction-deviation
#z_junction_deviation 0.0 # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
# Cartesian axis speed limits
x_axis_max_speed 30000 # Maximum speed in mm/min
y_axis_max_speed 30000 # Maximum speed in mm/min
z_axis_max_speed 300 # Maximum speed in mm/min
# Stepper module configuration
# Pins are defined as ports, and pin numbers, appending "!" to the number will invert a pin
# See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
alpha_step_pin 2.0 # Pin for alpha stepper step signal
alpha_dir_pin 0.5 # Pin for alpha stepper direction, add '!' to reverse direction
alpha_en_pin 0.4 # Pin for alpha enable pin
alpha_current 1.0 # X stepper motor current
alpha_max_rate 30000.0 # Maximum rate in mm/min
beta_step_pin 2.1 # Pin for beta stepper step signal
beta_dir_pin 0.11 # Pin for beta stepper direction, add '!' to reverse direction
beta_en_pin 0.10 # Pin for beta enable
beta_current 1.0 # Y stepper motor current
beta_max_rate 30000.0 # Maxmimum rate in mm/min
gamma_step_pin 2.2 # Pin for gamma stepper step signal
gamma_dir_pin 0.20 # Pin for gamma stepper direction, add '!' to reverse direction
gamma_en_pin 0.19 # Pin for gamma enable
gamma_current 1.0 # Z stepper motor current
gamma_max_rate 300.0 # Maximum rate in mm/min
## Extruder module configuration
# See http://smoothieware.org/extruder
extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
extruder.hotend.steps_per_mm 140 # Steps per mm for extruder stepper
extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec2
extruder.hotend.max_speed 50 # Maximum speed in mm/s
extruder.hotend.step_pin 2.3 # Pin for extruder step signal
extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal ( add '!' to reverse direction )
extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
# Extruder offset
#extruder.hotend.x_offset 0 # X offset from origin in mm
#extruder.hotend.y_offset 0 # Y offset from origin in mm
#extruder.hotend.z_offset 0 # Z offset from origin in mm
# Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
#extruder.hotend.retract_length 3 # Retract length in mm
#extruder.hotend.retract_feedrate 45 # Retract feedrate in mm/sec
#extruder.hotend.retract_recover_length 0 # Additional length for recover
#extruder.hotend.retract_recover_feedrate 8 # Recover feedrate in mm/sec (should be less than retract feedrate)
#extruder.hotend.retract_zlift_length 0 # Z-lift on retract in mm, 0 disables
#extruder.hotend.retract_zlift_feedrate 6000 # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
delta_current 1.5 # First extruder stepper motor current
# Second extruder module configuration
#extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
#extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
#extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
#extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
#extruder.hotend2.max_speed 50 # mm/s
#extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
#extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal ( add '!' to reverse direction )
#extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
#extruder.hotend2.x_offset 0 # x offset from origin in mm
#extruder.hotend2.y_offset 25.0 # y offset from origin in mm
#extruder.hotend2.z_offset 0 # z offset from origin in mm
#epsilon_current 1.5 # Second extruder stepper motor current
## Laser module configuration
# See http://smoothieware.org/laser
laser_module_enable false # Whether to activate the laser module at all
laser_module_pwm_pin 2.5 # This pin will be PWMed to control the laser.
# Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
# can be used since laser requires hardware PWM, see http://smoothieware.org/pinout
#laser_module_ttl_pin 1.30 # This pin turns on when the laser turns on, and off when the laser turns off.
#laser_module_maximum_power 1.0 # This is the maximum duty cycle that will be applied to the laser
#laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
# active without actually burning.
#laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
# the maximum and minimum power levels specified above
#laser_module_pwm_period 20 # This sets the pwm frequency as the period in microseconds
## Temperature control configuration
# See http://smoothieware.org/temperaturecontrol
# First hotend configuration
temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
temperature_control.hotend.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#toc5
#temperature_control.hotend.beta 4066 # Or set the beta value
temperature_control.hotend.set_m_code 104 # M-code to set the temperature for this module
temperature_control.hotend.set_and_wait_m_code 109 # M-code to set-and-wait for this module
temperature_control.hotend.designator T # Designator letter for this module
#temperature_control.hotend.max_temp 300 # Set maximum temperature - Will prevent heating above 300 by default
#temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set
# Safety control is enabled by default and can be overidden here, the values show the defaults
# See http://smoothieware.org/temperaturecontrol#runaway
#temperature_control.hotend.runaway_heating_timeout 900 # How long it can take to heat up, max is 2040 seconds.
#temperature_control.hotend.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
#temperature_control.hotend.runaway_range 20 # How far from the set temperature it can wander, max setting is 63°C
# PID configuration
# See http://smoothieware.org/temperaturecontrol#pid
#temperature_control.hotend.p_factor 13.7 # P ( proportional ) factor
#temperature_control.hotend.i_factor 0.097 # I ( integral ) factor
#temperature_control.hotend.d_factor 24 # D ( derivative ) factor
#temperature_control.hotend.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
# Second hotend configuration
#temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
#temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
#temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
#temperature_control.hotend2.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#thermistor
##temperature_control.hotend2.beta 4066 # or set the beta value
#temperature_control.hotend2.set_m_code 104 # M-code to set the temperature for this module
#temperature_control.hotend2.set_and_wait_m_code 109 # M-code to set-and-wait for this module
#temperature_control.hotend2.designator T1 # Designator letter for this module
#temperature_control.hotend2.p_factor 13.7 # P ( proportional ) factor
#temperature_control.hotend2.i_factor 0.097 # I ( integral ) factor
#temperature_control.hotend2.d_factor 24 # D ( derivative ) factor
#temperature_control.hotend2.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
temperature_control.bed.enable true # Whether to activate this ( "hotend" ) module at all.
temperature_control.bed.thermistor_pin 0.24 # Pin for the thermistor to read
temperature_control.bed.heater_pin 2.5 # Pin that controls the heater
temperature_control.bed.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
#temperature_control.bed.beta 3974 # Or set the beta value
temperature_control.bed.set_m_code 140 # M-code to set the temperature for this module
temperature_control.bed.set_and_wait_m_code 190 # M-code to set-and-wait for this module
temperature_control.bed.designator B # Designator letter for this module
# Bang-bang ( simplified ) control
# See http://smoothieware.org/temperaturecontrol#bang-bang
#temperature_control.bed.bang_bang false # Set to true to use bang bang control rather than PID
#temperature_control.bed.hysteresis 2.0 # Set to the temperature in degrees C to use as hysteresis
## Switch modules
# See http://smoothieware.org/switch
# Switch module for fan control
switch.fan.enable true # Enable this module
switch.fan.input_on_command M106 # Command that will turn this switch on
switch.fan.input_off_command M107 # Command that will turn this switch off
switch.fan.output_pin 2.6 # Pin this module controls
switch.fan.output_type pwm # PWM output settable with S parameter in the input_on_comand
#switch.fan.max_pwm 255 # Set max pwm for the pin default is 255
#switch.misc.enable true # Enable this module
#switch.misc.input_on_command M42 # Command that will turn this switch on
#switch.misc.input_off_command M43 # Command that will turn this switch off
#switch.misc.output_pin 2.4 # Pin this module controls
#switch.misc.output_type digital # Digital means this is just an on or off pin
## Temperatureswitch
# See http://smoothieware.org/temperatureswitch
# Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
# Useful to turn on a fan or water pump to cool the hotend
#temperatureswitch.hotend.enable true #
#temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
#temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
#temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
#temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
#temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
## Endstops
# See http://smoothieware.org/endstops
endstops_enable true # The endstop module is enabled by default and can be disabled here
#corexy_homing false # Set to true if homing on a hbot or corexy
alpha_min_endstop 1.24^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
#alpha_max_endstop 1.25^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
alpha_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
alpha_min 0 # This gets loaded as the current position after homing when home_to_min is set
alpha_max 200 # This gets loaded as the current position after homing when home_to_max is set
beta_min_endstop 1.26^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
#beta_max_endstop 1.27^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
beta_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
beta_min 0 # This gets loaded as the current position after homing when home_to_min is set
beta_max 200 # This gets loaded as the current position after homing when home_to_max is set
gamma_min_endstop 1.28^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
#gamma_max_endstop 1.29^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
gamma_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
gamma_min 0 # This gets loaded as the current position after homing when home_to_min is set
gamma_max 200 # This gets loaded as the current position after homing when home_to_max is set
alpha_max_travel 500 # Max travel in mm for alpha/X axis when homing
beta_max_travel 500 # Max travel in mm for beta/Y axis when homing
gamma_max_travel 500 # Max travel in mm for gamma/Z axis when homing
# Optional enable limit switches, actions will stop if any enabled limit switch is triggered
#alpha_limit_enable false # Set to true to enable X min and max limit switches
#beta_limit_enable false # Set to true to enable Y min and max limit switches
#gamma_limit_enable false # Set to true to enable Z min and max limit switches
# Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
alpha_fast_homing_rate_mm_s 50 # Alpha/X fast homing feedrate in mm/second
alpha_slow_homing_rate_mm_s 25 # Alpha/X slow homing feedrate in mm/second
beta_fast_homing_rate_mm_s 50 # Beta/Y fast homing feedrate in mm/second
beta_slow_homing_rate_mm_s 25 # Beta/Y slow homing feedrate in mm/second
gamma_fast_homing_rate_mm_s 4 # Gamma/Z fast homing feedrate in mm/second
gamma_slow_homing_rate_mm_s 2 # Gamma/Z slow homing feedrate in mm/second
alpha_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for alpha/X
beta_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for beta/Y
gamma_homing_retract_mm 2 # Distance to retract from the endstop after it is hit for gamma/Z
# Optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
#alpha_limit_enable false # Set to true to enable X min and max limit switches
#beta_limit_enable false # Set to true to enable Y min and max limit switches
#gamma_limit_enable false # Set to true to enable Z min and max limit switches
# Optional order in which axis will home, default is they all home at the same time,
# If this is set it will force each axis to home one at a time in the specified order
#homing_order XYZ # X axis followed by Y then Z last
#move_to_origin_after_home false # Move XY to 0,0 after homing
#endstop_debounce_count 100 # Uncomment if you get noise on your endstops, default is 100
#endstop_debounce_ms 1 # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
#home_z_first true # Uncomment and set to true to home the Z first, otherwise Z homes after XY
# End of endstop config
# Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
#include abc-endstop.config
## Z-probe
# See http://smoothieware.org/zprobe
zprobe.enable false # Set to true to enable a zprobe
zprobe.probe_pin 1.28!^ # Pin probe is attached to, if NC remove the !
zprobe.slow_feedrate 5 # Mm/sec probe feed rate
#zprobe.debounce_ms 1 # Set if noisy
zprobe.fast_feedrate 100 # Move feedrate mm/sec
zprobe.probe_height 5 # How much above bed to start probe
#gamma_min_endstop nc # Normally 1.28. Change to nc to prevent conflict,
# Levelling strategy
# Example for 3-point levelling strategy, see wiki documentation for other strategies
#leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
#leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
#leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
#leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
#leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
#leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
#leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
#leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
## Panel
# See http://smoothieware.org/panel
# Please find your panel on the wiki and copy/paste the right configuration here
panel.enable true # Set to true to enable the panel code
# Example for reprap discount GLCD
# on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
# +5v is EXP1 pin 10, Gnd is EXP1 pin 9
panel.lcd reprap_discount_glcd #
panel.spi_channel 0 # SPI channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
panel.spi_cs_pin 0.16 # SPI chip select ; GLCD EXP1 Pin 4
panel.encoder_a_pin 3.25!^ # Encoder pin ; GLCD EXP2 Pin 3
panel.encoder_b_pin 3.26!^ # Encoder pin ; GLCD EXP2 Pin 5
panel.encoder_resolution 2
panel.click_button_pin 1.30!^ # Click button ; GLCD EXP1 Pin 2
panel.buzz_pin 1.31 # Pin for buzzer ; GLCD EXP1 Pin 1
panel.back_button_pin 2.11!^ # Back button ; GLCD EXP2 Pin 8
panel.external_sd true # set to true if there is an extrernal sdcard on the panel
panel.external_sd.spi_channel 1 # set spi channel the sdcard is on
panel.external_sd.spi_cs_pin 0.28 # set spi chip select for the sdcard (or any spare pin)
panel.external_sd.sdcd_pin 0.27!^ # sd detect signal (set to nc if no sdcard detect) (or any spare pin)
# pins used with other panels
#panel.up_button_pin 0.1! # up button if used
#panel.down_button_pin 0.0! # down button if used
#panel.click_button_pin 0.18! # click button if used
panel.menu_offset 1 # Some panels will need 1 here
panel.alpha_jog_feedrate 6000 # X jogging feedrate in mm/min
panel.beta_jog_feedrate 6000 # Y jogging feedrate in mm/min
panel.gamma_jog_feedrate 200 # Z jogging feedrate in mm/min
panel.hotend_temperature 185 # Temp to set hotend when preheat is selected
panel.bed_temperature 40 # Temp to set bed when preheat is selected
## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
# NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
custom_menu.power_on.enable true #
custom_menu.power_on.name Power_on #
custom_menu.power_on.command M80 #
custom_menu.power_off.enable true #
custom_menu.power_off.name Power_off #
custom_menu.power_off.command M81 #
## Network settings
# See http://smoothieware.org/network
network.enable false # Enable the ethernet network services
network.webserver.enable true # Enable the webserver
network.telnet.enable true # Enable the telnet server
network.ip_address auto # Use dhcp to get ip address
# Uncomment the 3 below to manually setup ip address
#network.ip_address 192.168.3.222 # The IP address
#network.ip_mask 255.255.255.0 # The ip mask
#network.ip_gateway 192.168.3.1 # The gateway address
#network.mac_override xx.xx.xx.xx.xx.xx # Override the mac address, only do this if you have a conflict
## System configuration
# Serial communications configuration ( baud rate defaults to 9600 if undefined )
# For communication over the UART port, *not* the USB/Serial port
uart0.baud_rate 250000 # Baud rate for the default hardware ( UART ) serial port
second_usb_serial_enable false # This enables a second USB serial port
#leds_disable true # Disable using leds after config loaded
#play_led_disable true # Disable the play led
# Kill button maybe assigned to a different pin, set to the onboard pin by default
# See http://smoothieware.org/killbutton
kill_button_enable true # Set to true to enable a kill button
kill_button_pin 2.12 # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
#msd_disable false # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
#dfu_enable false # For linux developers, set to true to enable DFU
# Only needed on a smoothieboard
# See http://smoothieware.org/currentcontrol
currentcontrol_module_enable true # Control stepper motor current via the configuration file
Ewentualne pytanie które teraz mi podsunąłeś czy TFT będzie działał z marlinem?
UltiAnet 240x240x290,
Wielka Siostra 430x430x400
Wielka Siostra 430x430x400
- FlameRunner
- Zasłużony
- Postów w temacie: 1
- Posty: 6568
- Rejestracja: 15 kwie 2016, 21:26
- x 2056
Re: Sbase V1.3 + TFT32 - pomocy przy uruchamianiu.
Koniecznie przeczytaj: viewtopic.php?f=20&t=3266remus pisze:Sami spece, podstawa Smoti działa stabilnie tylko na25000 inaczej życzę powodzenia.Kod: Zaznacz cały
## System configuration # Serial communications configuration ( baud rate defaults to 9600 if undefined ) # For communication over the UART port, *not* the USB/Serial port uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port
Co do wgrywania, config.txt na płycie czyli włożoną kartę musisz mieć do Sbase, po wgraniu bo go nie wgrywa (tylko ram) pozostaje na tym samym rozszerzeniu. Karty nie musisz wyciągać zmieniasz config na Sbase przez USB lub wifi i reset
W TFT po wgraniu masz chyba .cue więc się wgrało na tft tez budrate 250000.
Elektronika jest bardzo dobra mam na myśli Sbase drukarka robi dużo lepsze wydruki jak na 8 bitowcu, za to wyświetlacz pozostawia wiele do życzenia
rafaljot po co podrzucasz stare linki, jak nie możesz pomóc to nie wpisuj nic.
Szczególną uwagę zwróć na stosowanie bloczków z kodem, uzyskiwanych z użyciem znaczników "code". Dla przykładu zmodyfikowałem cytowany post.
PS Potraktuj powyższe jako słowne ostrzeżenie - regulamin forum III.3.b.
- zen
- Konto z ograniczeniami
- Postów w temacie: 3
- Posty: 295
- Rejestracja: 26 lut 2017, 20:53
- Lokalizacja: Poznań miasto doznań
- Drukarka: Too many
- x 34
- Kontakt:
Re: Sbase V1.3 + TFT32 - pomocy przy uruchamianiu.
Gościu, może sobie piwko trzepniesz na rozluźnienie? To chyba oczywiste, że musisz zmienić rodzaj firmware na własny.remus pisze:Wprowadzasz człowieka w błąd i nie czytasz ze zrozumieniem.
Kolega założył topik "Sbase V1.3 + TFT32 "
A ty mu proponujesz konfigurację:
#mainboard firmware setting(marlin:1; repetier:2; smoothie:3)
>cfg_firmware_type:1
Jak już się poddacie to dam całą konfigurację działającą dla płyty i tft
rafaljot kolego ja nie muszę nic układać to wy się motacie i wprowadzacie ludzi w błąd udając speców.
Dlatego jest 300 wpisów i brak rezultatów. Powyżej Wasze mądrości.
Dla tej części kodu prawidłowo:
#mainboard firmware setting(marlin:1; repetier:2; smoothie:3)
>cfg_firmware_type:3
No i doucz się - na SBase doskonale działa Marlin 2.0. Używam od roku bez żadnych problemów, w przeciwieństwie do Smoothieware.
Mendel / i3 / i3 Alu / P3Steel / HEVO^300 / Delta Kossel Linear Plus / Prusa MK3S + MMU / Voron / Bambu X1C + AMS
- MarioM06
- Konto z ograniczeniami
- Postów w temacie: 10
- Posty: 113
- Rejestracja: 05 maja 2018, 11:44
- Lokalizacja: Goczałkowice-Zdrój
- x 29
Re: Sbase V1.3 + TFT32 - pomocy przy uruchamianiu.
Trochę się podbawiłem z Marlin firmware na Sbase i SKR 1.1 która też ostatnio do mnie dotarła w komplecie z ReprapDiscount Full Graphic Smart Controller. I pojawiły się nowe problemy
A więc głównie chodzi mi o to, że ani Sbase ani SKR 1.1 nie odczytuje nic z karty SD przy wyświetlaczu, w ogóle jej nie "widzą". A ze Smoothie na Sbase normalnie drukowałem z karty przy graficznym jak i TFT.
Na SKR 1.1 wrzuciłem Configuration.h, Configuration_adv.h i platformio.ini od arkomania.pl ale karty SD i tak nie widzi.
Oczywiście Marlin się zainstalował na obu płytkach i wyświetlacze graficzne też działają. Z TFT jeszcze mi się nie udało odpalić tego.
Poradzicie coś??
A więc głównie chodzi mi o to, że ani Sbase ani SKR 1.1 nie odczytuje nic z karty SD przy wyświetlaczu, w ogóle jej nie "widzą". A ze Smoothie na Sbase normalnie drukowałem z karty przy graficznym jak i TFT.
Na SKR 1.1 wrzuciłem Configuration.h, Configuration_adv.h i platformio.ini od arkomania.pl ale karty SD i tak nie widzi.
Oczywiście Marlin się zainstalował na obu płytkach i wyświetlacze graficzne też działają. Z TFT jeszcze mi się nie udało odpalić tego.
Poradzicie coś??
UltiAnet 240x240x290,
Wielka Siostra 430x430x400
Wielka Siostra 430x430x400
-
- Konto z ograniczeniami
- Postów w temacie: 4
- Posty: 629
- Rejestracja: 15 lip 2017, 16:07
- Drukarka: Hypercube Evolution
- x 100
Re: Sbase V1.3 + TFT32 - pomocy przy uruchamianiu.
Poradzę przeczytać co jest napisane w pliku konfiguracyjnym z przykładów do sbase i pliku z ustawieniami pinów, a nie wrzucać na ślepo gotowce od innych.
- MarioM06
- Konto z ograniczeniami
- Postów w temacie: 10
- Posty: 113
- Rejestracja: 05 maja 2018, 11:44
- Lokalizacja: Goczałkowice-Zdrój
- x 29
Re: Sbase V1.3 + TFT32 - pomocy przy uruchamianiu.
Czyli żeby korzystać z karty SD wyświetlacza z Marlinem obrócenie wtyczek EXP1 i EXP2 0 180* nie wystarcza. Trzeba ciąć kabel i dodatkowo edytować piny tak? Dobrze zrozumiałem?
UltiAnet 240x240x290,
Wielka Siostra 430x430x400
Wielka Siostra 430x430x400