reprapy.pl

Kod: Zaznacz cały

; generated by PrusaSlicer 2.2.0+linux-x64 on 2020-09-23 at 08:21:26 UTC
; external perimeters extrusion width = 0.45mm
; perimeters extrusion width = 0.45mm
; infill extrusion width = 0.45mm
; solid infill extrusion width = 0.45mm
; top infill extrusion width = 0.42mm
; first layer extrusion width = 0.42mm


; filament used [mm] = 6758.1
; filament used [cm3] = 16.3
; filament used [g] = 21.1
; filament cost = 1.4

; total filament used [g] = 21.1
; total filament cost = 1.4
; estimated printing time (normal mode) = 2h 9m 27s

; avoid_crossing_perimeters = 0
; bed_custom_model = 
; bed_custom_texture = 
; bed_shape = 0x0,290x0,290x280,0x280
; bed_temperature = 60
; before_layer_gcode = 
; between_objects_gcode = 
; bottom_fill_pattern = rectilinear
; bottom_solid_layers = 4
; bottom_solid_min_thickness = 0
; bridge_acceleration = 0
; bridge_angle = 0
; bridge_fan_speed = 100
; bridge_flow_ratio = 0.95
; bridge_speed = 50
; brim_width = 0
; clip_multipart_objects = 1
; compatible_printers_condition_cummulative = ;(printer_notes=~/.*PRINTER_VENDOR_HEVO.*/)
; complete_objects = 0
; cooling = 1
; cooling_tube_length = 5
; cooling_tube_retraction = 91.5
; default_acceleration = 0
; default_filament_profile = 
; default_print_profile = 
; deretract_speed = 36
; disable_fan_first_layers = 3
; dont_support_bridges = 1
; draft_shield = 0
; duplicate_distance = 6
; elefant_foot_compensation = 0
; end_filament_gcode = "; Filament-specific end gcode"
; end_gcode = M104 S0 ;extruder heater off\nM140 S0 ;heated bed heater off (if you have it)\nG91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 X-2 Y-2 Z+1 E-5 F3000 ;move Z up a bit and retract filament even more\nM81 S1\nG90 ;absolute positioning\nG1 X5 Y5 F10000 ;move Z up a bit and retract filament even more\nG28 Y ;move X/Y to min endstops, so the head is out of the way\nG28 X\nM84 ;steppers off\nG90 ;absolute positioning\nM104 S0 ; turn off temperature\nM84 ; disable motors\n
; ensure_vertical_shell_thickness = 0
; external_perimeter_extrusion_width = 0.45
; external_perimeter_speed = 70
; external_perimeters_first = 0
; extra_loading_move = -2
; extra_perimeters = 1
; extruder_clearance_height = 24
; extruder_clearance_radius = 40
; extruder_colour = ""
; extruder_offset = 0x0
; extrusion_axis = E
; extrusion_multiplier = 1.075
; extrusion_width = 0.45
; fan_always_on = 0
; fan_below_layer_time = 100
; filament_colour = #FFFFFF
; filament_cooling_final_speed = 3.4
; filament_cooling_initial_speed = 2.2
; filament_cooling_moves = 4
; filament_cost = 65
; filament_density = 1.3
; filament_diameter = 1.75
; filament_load_time = 0
; filament_loading_speed = 28
; filament_loading_speed_start = 3
; filament_max_volumetric_speed = 15
; filament_minimal_purge_on_wipe_tower = 15
; filament_notes = "For MZ 0.98 flow"
; filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
; filament_settings_id = "TempTower_v2.3mf (Generic PLA HDC)"
; filament_soluble = 0
; filament_toolchange_delay = 0
; filament_type = PLA
; filament_unload_time = 0
; filament_unloading_speed = 90
; filament_unloading_speed_start = 100
; filament_vendor = (Unknown)
; fill_angle = 45
; fill_density = 10%
; fill_pattern = rectilinear
; first_layer_acceleration = 0
; first_layer_bed_temperature = 60
; first_layer_extrusion_width = 0.42
; first_layer_height = 0.16
; first_layer_speed = 30
; first_layer_temperature = 220
; gap_fill_speed = 70
; gcode_comments = 0
; gcode_flavor = reprap
; gcode_label_objects = 1
; high_current_on_filament_swap = 0
; host_type = duet
; infill_acceleration = 0
; infill_every_layers = 1
; infill_extruder = 1
; infill_extrusion_width = 0.45
; infill_first = 0
; infill_only_where_needed = 0
; infill_overlap = 25%
; infill_speed = 70
; interface_shells = 0
; layer_gcode = 
; layer_height = 0.2
; machine_max_acceleration_e = 5000,5000
; machine_max_acceleration_extruding = 1500,1250
; machine_max_acceleration_retracting = 1500,1250
; machine_max_acceleration_x = 1500,1000
; machine_max_acceleration_y = 1500,1000
; machine_max_acceleration_z = 20,200
; machine_max_feedrate_e = 100,120
; machine_max_feedrate_x = 150,200
; machine_max_feedrate_y = 150,200
; machine_max_feedrate_z = 3,12
; machine_max_jerk_e = 5,2.5
; machine_max_jerk_x = 8,10
; machine_max_jerk_y = 8,10
; machine_max_jerk_z = 0.3,0.4
; machine_min_extruding_rate = 0,0
; machine_min_travel_rate = 0,0
; max_fan_speed = 90
; max_layer_height = 0.3
; max_print_height = 300
; max_print_speed = 150
; max_volumetric_speed = 0
; min_fan_speed = 70
; min_layer_height = 0.06
; min_print_speed = 15
; min_skirt_length = 20
; notes = 
; nozzle_diameter = 0.4
; only_retract_when_crossing_perimeters = 0
; ooze_prevention = 0
; output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{print_time}.gcode
; overhangs = 1
; parking_pos_retraction = 92
; perimeter_acceleration = 0
; perimeter_extruder = 1
; perimeter_extrusion_width = 0.45
; perimeter_speed = 70
; perimeters = 2
; post_process = 
; print_settings_id = TempTower_v2.3mf (0.20mm NORMAL HDC)
; printer_model = 
; printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_HEVO\nPRINTER_MODEL_DC\nPRINTER_HAS_BOWDEN
; printer_settings_id = HEVO Dc
; printer_technology = FFF
; printer_variant = 
; printer_vendor = 
; raft_layers = 0
; remaining_times = 0
; resolution = 0
; retract_before_travel = 1
; retract_before_wipe = 100%
; retract_layer_change = 1
; retract_length = 2
; retract_length_toolchange = 10
; retract_lift = 0
; retract_lift_above = 0
; retract_lift_below = 0.6
; retract_restart_extra = 0
; retract_restart_extra_toolchange = 0
; retract_speed = 14
; seam_position = nearest
; serial_port = 
; serial_speed = 250000
; silent_mode = 0
; single_extruder_multi_material = 0
; single_extruder_multi_material_priming = 1
; skirt_distance = 3
; skirt_height = 1
; skirts = 2
; slice_closing_radius = 0.049
; slowdown_below_layer_time = 20
; small_perimeter_speed = 70
; solid_infill_below_area = 0
; solid_infill_every_layers = 0
; solid_infill_extruder = 1
; solid_infill_extrusion_width = 0.45
; solid_infill_speed = 70
; spiral_vase = 0
; standby_temperature_delta = -5
; start_filament_gcode = "M207 S[retract_length] F{retract_speed[0]*60} Z0\nM572 D0 S0.0\n"
; start_gcode = M80\nG4 S2\nG21 ;metric values\nG90 ;absolute positioning\nM107 ;start with the fan off\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM280 P3 S260 I1\nG28\nM104 S[first_layer_temperature] ; set extruder temp\nG1 X5 Y5 F3000\nM109 S[first_layer_temperature] ; wait for extruder temp\nM204 P2000 T4000
; support_material = 0
; support_material_angle = 0
; support_material_auto = 1
; support_material_buildplate_only = 0
; support_material_contact_distance = 0.2
; support_material_enforce_layers = 0
; support_material_extruder = 0
; support_material_extrusion_width = 0.35
; support_material_interface_contact_loops = 0
; support_material_interface_extruder = 0
; support_material_interface_layers = 2
; support_material_interface_spacing = 0.2
; support_material_interface_speed = 100%
; support_material_pattern = rectilinear
; support_material_spacing = 2
; support_material_speed = 50
; support_material_synchronize_layers = 0
; support_material_threshold = 45
; support_material_with_sheath = 0
; support_material_xy_spacing = 60%
; temperature = 240
; thin_walls = 0
; threads = 12
; thumbnails = 
; toolchange_gcode = 
; top_fill_pattern = rectilinear
; top_infill_extrusion_width = 0.42
; top_solid_infill_speed = 70
; top_solid_layers = 4
; top_solid_min_thickness = 0
; travel_speed = 300
; use_firmware_retraction = 1
; use_relative_e_distances = 1
; use_volumetric_e = 0
; variable_layer_height = 1
; wipe = 0
; wipe_into_infill = 0
; wipe_into_objects = 0
; wipe_tower = 0
; wipe_tower_bridging = 10
; wipe_tower_no_sparse_layers = 0
; wipe_tower_rotation_angle = 0
; wipe_tower_width = 60
; wipe_tower_x = 180
; wipe_tower_y = 140
; wiping_volumes_extruders = 70,70
; wiping_volumes_matrix = 0
; xy_size_compensation = 0
; z_offset = 0