UltiV-slot XD 2
- Janek_Porzycz
- Postów w temacie: 76
- Posty: 743
- Rejestracja: 26 wrz 2019, 22:15
- Lokalizacja: Warszawa
- Drukarka: K1 Max, Ender 3 V3SE
- x 491
Re: UltiV-slot XD 2
Wyglada na to ze plytke mozna zamontowac jak sie chce. To bardzo dobrze bo slabo z miejscem
M955: Configure Accelerometer
Support Marlin RepRapFirmware Repetier Smoothie Klipper Prusa MK4duo MakerBot
No 3.4+ No No ??? No No ???
grbl Sprinter BFB FiveD Machinekit Redeem Teacup Yaskawa
??? No No No No ??? No No
Parameters (provisional)
Pnn or Pbb.nn Accelerometer to use (required)
Inn Accelerometer orientation
Snnn Sample rate (Hz)
Rnn Resolution (bits), typically 8, 10 or 12
This command configures an accelerometer.
The P parameter selects which accelerometer to use and is mandatory. To use an accelerometer on a CAN-connected expansion board, use the form Pboard-address.device-number for example P22.0.
If none of the other parameters are provided, the current configuration of the specified accelerometer is reported. Otherwise the configuration of that accelerometer is adjusted according to the I, S, and R parameters. These configuration settings persist until they are changed.
The I (orientation) parameter tells the firmware which of the 24 possible orientations the accelerometer chip is in relative to the printer axes. It is expressed as a 2-digit number. The first digit specifies which machine direction the Z axis of the accelerometer chip (usually the top face of the chip) faces, as follows: 0 = +X, 1 = +Y, 2 = +Z, 4 = -X, 5 = -Y, 6 = -Z. The second digit expresses which direction the X axis of the accelerometer chip faces, using the same code. If the accelerometer chip axes line up with the machine axis, the orientation is 21. This is the default orientation if no orientation has been specified.
The S and R parameters control how the accelerometer is programmed. The R parameter is ignored unless the S parameter is also provided. If S is provided but R is missing, a default resolution is used. The sensor resolution will be adjusted to be no greater than the value of the R parameter (or the minimum supported resolution if greater), then the sensor sampling rate will be adjusted to a value supported at that resolution that is close to the S parameter. The actual rate and resolution selected can be found by using M955 with just the P parameter.
M955: Configure Accelerometer
Support Marlin RepRapFirmware Repetier Smoothie Klipper Prusa MK4duo MakerBot
No 3.4+ No No ??? No No ???
grbl Sprinter BFB FiveD Machinekit Redeem Teacup Yaskawa
??? No No No No ??? No No
Parameters (provisional)
Pnn or Pbb.nn Accelerometer to use (required)
Inn Accelerometer orientation
Snnn Sample rate (Hz)
Rnn Resolution (bits), typically 8, 10 or 12
This command configures an accelerometer.
The P parameter selects which accelerometer to use and is mandatory. To use an accelerometer on a CAN-connected expansion board, use the form Pboard-address.device-number for example P22.0.
If none of the other parameters are provided, the current configuration of the specified accelerometer is reported. Otherwise the configuration of that accelerometer is adjusted according to the I, S, and R parameters. These configuration settings persist until they are changed.
The I (orientation) parameter tells the firmware which of the 24 possible orientations the accelerometer chip is in relative to the printer axes. It is expressed as a 2-digit number. The first digit specifies which machine direction the Z axis of the accelerometer chip (usually the top face of the chip) faces, as follows: 0 = +X, 1 = +Y, 2 = +Z, 4 = -X, 5 = -Y, 6 = -Z. The second digit expresses which direction the X axis of the accelerometer chip faces, using the same code. If the accelerometer chip axes line up with the machine axis, the orientation is 21. This is the default orientation if no orientation has been specified.
The S and R parameters control how the accelerometer is programmed. The R parameter is ignored unless the S parameter is also provided. If S is provided but R is missing, a default resolution is used. The sensor resolution will be adjusted to be no greater than the value of the R parameter (or the minimum supported resolution if greater), then the sensor sampling rate will be adjusted to a value supported at that resolution that is close to the S parameter. The actual rate and resolution selected can be found by using M955 with just the P parameter.
- Janek_Porzycz
- Postów w temacie: 76
- Posty: 743
- Rejestracja: 26 wrz 2019, 22:15
- Lokalizacja: Warszawa
- Drukarka: K1 Max, Ender 3 V3SE
- x 491
Re: UltiV-slot XD 2
Dobra chyba tak to bedzie:
Trza bedzie troche poborowac ;P
I chyba jeszcze tu odchudze troche.
Trza bedzie troche poborowac ;P
I chyba jeszcze tu odchudze troche.
- Pjoter
- Drukarz
- Postów w temacie: 3
- Posty: 2015
- Rejestracja: 16 lis 2017, 18:53
- Lokalizacja: Gdańsk
- Drukarka: HEVO, MK3S
- x 881
Re: UltiV-slot XD 2
Czy ten akcelerometr na stałe mocujesz? czy tylko na czas pomiaru i kalibracji? Bo chyba nie trzeba mieć cały czas zamontowanego. Czy może jest jakaś opcja "live auto tune"?
Moje wydruki | Thingiverse | PrusaPrinters
Anycubic i3 Mega - sprzedana
HyperCube Evolution #1 - worklog
Ender-2 - sprzedana
Prusa MK3S - odkupiona używana
HyperCube Evolution #2 - szukam na nią miejsca na razie w odstawce
Anycubic i3 Mega - sprzedana
HyperCube Evolution #1 - worklog
Ender-2 - sprzedana
Prusa MK3S - odkupiona używana
HyperCube Evolution #2 - szukam na nią miejsca na razie w odstawce
- Janek_Porzycz
- Postów w temacie: 76
- Posty: 743
- Rejestracja: 26 wrz 2019, 22:15
- Lokalizacja: Warszawa
- Drukarka: K1 Max, Ender 3 V3SE
- x 491
Re: UltiV-slot XD 2
Montuje na stale z lenistwa. Nie ma chyba nic ala "live" ale przy np zmianie naciagu paskow itd. Trza kalibrowac od nowa
- Pjoter
- Drukarz
- Postów w temacie: 3
- Posty: 2015
- Rejestracja: 16 lis 2017, 18:53
- Lokalizacja: Gdańsk
- Drukarka: HEVO, MK3S
- x 881
Re: UltiV-slot XD 2
Kumam, nie pomyślałem o tym
Moje wydruki | Thingiverse | PrusaPrinters
Anycubic i3 Mega - sprzedana
HyperCube Evolution #1 - worklog
Ender-2 - sprzedana
Prusa MK3S - odkupiona używana
HyperCube Evolution #2 - szukam na nią miejsca na razie w odstawce
Anycubic i3 Mega - sprzedana
HyperCube Evolution #1 - worklog
Ender-2 - sprzedana
Prusa MK3S - odkupiona używana
HyperCube Evolution #2 - szukam na nią miejsca na razie w odstawce
- czasnagli
- Postów w temacie: 4
- Posty: 196
- Rejestracja: 18 lis 2019, 19:07
- Lokalizacja: Warszawa
- Drukarka: custom CoreXY
- x 64
Re: UltiV-slot XD 2
Ja się zawsze zastanawiam jak input shaping działa w różnych pozycjach stołu bo zdaje się, że kalibracja robiona jest na środku stołu. A co ze zmianą temperatury?Janek_Porzycz pisze:Montuje na stale z lenistwa. Nie ma chyba nic ala "live" ale przy np zmianie naciagu paskow itd. Trza kalibrowac od nowa
Daj Pan znać jak to uruchomisz, bo moduły BTT i Mellow czekają aby uruchomić RRF
- Janek_Porzycz
- Postów w temacie: 76
- Posty: 743
- Rejestracja: 26 wrz 2019, 22:15
- Lokalizacja: Warszawa
- Drukarka: K1 Max, Ender 3 V3SE
- x 491
Re: UltiV-slot XD 2
tu nie chodzi o pozycje tylko o czestotliwosc zmiany kierunku i o wyeliminowanie rezonansu osi ktory objawia sie ringingiem:
obejrzyj sobie:
https://youtu.be/er7q-CJL1lc?t=870
obejrzyj sobie:
https://youtu.be/er7q-CJL1lc?t=870
- czasnagli
- Postów w temacie: 4
- Posty: 196
- Rejestracja: 18 lis 2019, 19:07
- Lokalizacja: Warszawa
- Drukarka: custom CoreXY
- x 64
Re: UltiV-slot XD 2
Tak jest, ale ringing zmienia się w zależności od pozycji na stole - im głowica bliżej silnika, tym krótszy pasek i wyższa częstotliwość drgań paska. Ciekawsza sytuacja jest jeszcze ze sposobem montażu stołu. Cantilever, na dwóch śrubach, na trzech - w każdym z tych jest inny efekt w zależności od miejsca na stole.Janek_Porzycz pisze:tu nie chodzi o pozycje tylko o czestotliwosc zmiany kierunku i o wyeliminowanie rezonansu osi ktory objawia sie ringingiem:
obejrzyj sobie:
https://youtu.be/er7q-CJL1lc?t=870
Robił ktoś może wydruk skalibrowanego IS w 9 miejscach na stole?
- Janek_Porzycz
- Postów w temacie: 76
- Posty: 743
- Rejestracja: 26 wrz 2019, 22:15
- Lokalizacja: Warszawa
- Drukarka: K1 Max, Ender 3 V3SE
- x 491
Re: UltiV-slot XD 2
kurna mam nadzieje ze ktos kto to pisal (IS) to o tym tez pomyslal. Pewnie jak skoncze ten projekt to wszystkie zastosowane pomysly i nowinki beda juz ujowe tak btwczasnagli pisze:Tak jest, ale ringing zmienia się w zależności od pozycji na stole - im głowica bliżej silnika, tym krótszy pasek i wyższa częstotliwość drgań paska. Ciekawsza sytuacja jest jeszcze ze sposobem montażu stołu. Cantilever, na dwóch śrubach, na trzech - w każdym z tych jest inny efekt w zależności od miejsca na stole.Janek_Porzycz pisze:tu nie chodzi o pozycje tylko o czestotliwosc zmiany kierunku i o wyeliminowanie rezonansu osi ktory objawia sie ringingiem:
obejrzyj sobie:
https://youtu.be/er7q-CJL1lc?t=870
Robił ktoś może wydruk skalibrowanego IS w 9 miejscach na stole?
- Pjoter
- Drukarz
- Postów w temacie: 3
- Posty: 2015
- Rejestracja: 16 lis 2017, 18:53
- Lokalizacja: Gdańsk
- Drukarka: HEVO, MK3S
- x 881
Re: UltiV-slot XD 2
Skoro tak jest, to widziałeś znaczną różnicę do tej pory (bez IS)? Bo ja nie widziałem różnicy w jakości detalu zależnie od położenia na stole
Moje wydruki | Thingiverse | PrusaPrinters
Anycubic i3 Mega - sprzedana
HyperCube Evolution #1 - worklog
Ender-2 - sprzedana
Prusa MK3S - odkupiona używana
HyperCube Evolution #2 - szukam na nią miejsca na razie w odstawce
Anycubic i3 Mega - sprzedana
HyperCube Evolution #1 - worklog
Ender-2 - sprzedana
Prusa MK3S - odkupiona używana
HyperCube Evolution #2 - szukam na nią miejsca na razie w odstawce